Selector Lever Cable and Bracket - Floor Shift

Selector Lever Cable and Bracket - Floor Shift









Removal

All vehicles

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Jacking and Lifting Service and Repair.

Expedition

2. Remove the selector lever trim ring, console tray and cup holder insert.





3. Remove the screw and the console upper trim.





4. NOTE: The selector lever bezel has been removed from art for clarity. Do not remove the selector lever bezel.

Disconnect the selector lever cable from the selector lever.

1. Disconnect the selector lever cable from the selector lever arm.

2. Disconnect the selector lever cable from the selector lever housing.





Navigator

5. Remove the selector lever trim ring.





6. NOTE: Using a suitable tool, lift and remove the floor console upper panel from the rear.

Remove the floor console upper panel.





7. NOTE: The selector lever bezel has been removed from art for clarity. Do not remove the selector lever bezel.

Disconnect the selector lever cable from the selector lever arm.





8. Remove the center console LH finish panel.





9. Disconnect the selector lever cable from the selector lever housing.





All vehicles

10. Remove the selector lever cable and rubber grommet.





11. If equipped, remove the heat shield.





12. NOTICE: To prevent selector lever cable damage, do not apply force to the selector lever cable between the manual control lever and the selector lever cable bracket.

Move the locking tab up and disconnect the selector lever cable from the manual control lever.





13. Remove the selector lever cable clip to release the selector lever cable from the selector lever cable bracket.





14. Remove the bolts and the selector lever cable bracket from the transmission.





Installation

All vehicles

1. Install the selector lever cable bracket and bolts onto the transmission.
- Tighten to 25 Nm (18 lb-ft).





2. NOTICE: To prevent selector lever cable damage, do not apply force to the selector lever cable between the manual control lever and the selector lever cable bracket.

NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place. Press the selector lever cable into the selector lever cable bracket and listen for the selector lever cable to click into place. Pull back on the selector lever cable to make sure that the selector lever is locked into the selector lever cable bracket.

Install the selector lever cable into the selector lever cable bracket.





3. NOTE: When installing the selector lever cable end, make sure that the selector lever cable end is securely installed onto the manual control lever. Pull back on the selector lever cable to make sure that the selector cable end is securely installed onto the manual control lever.

Connect the selector lever cable onto the manual control lever.

- Listen for the audible click.

- Pull back on the selector lever cable to make sure that it is securely installed.





4. Lock the selector lever cable lock tab.





5. NOTE: Install a new heat shield if it is loose on the cable.

If equipped, install the heat shield.





6. Install the selector lever cable and rubber grommet.





Expedition

7. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place. Press the selector lever cable into the bracket and listen for the selector lever cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket.

NOTE: The selector lever bezel has been removed from art for clarity. Do not remove the selector lever bezel.

Connect the selector lever cable onto the selector lever.

1. Connect the selector lever cable onto the selector lever housing.
- Listen for the audible click.

- Pull back on the selector lever cable to make sure that it is securely installed.

2. Connect the selector lever cable onto the selector lever arm.
- Listen for the audible click.

- Pull back on the selector lever cable to make sure that it is securely installed.





8. Install the console upper trim and the screw.





9. Install the selector lever trim ring, console tray and cup holder insert.





Navigator

10. NOTE: When installing the selector lever cable, make sure that the selector lever cable locking tabs are locked in place. Press the selector lever cable into the bracket and listen for the selector lever cable to click into place. Pull back on the selector lever cable to make sure that it is locked into the bracket.

Connect the selector lever cable onto the selector lever housing.





11. Install the center console LH finish panel.





12. NOTE: When installing the selector lever cable end, make sure that the selector lever cable end is securely installed onto the selector lever ball stud. Pull back on the selector lever cable to make sure that the selector cable end is securely installed onto the selector lever ball stud.

NOTE: The selector lever bezel has been removed from art for clarity. Do not remove the selector lever bezel.

Connect the selector lever cable onto the selector lever arm.

- Listen for the audible click.

- Pull back on the selector lever cable to make sure that it is securely installed.





13. Install the floor console upper panel.





14. Install the selector lever trim ring.





All vehicles

15. Adjust the selector lever cable. For additional information, refer to Selector Lever Cable Adjustment Adjustments.