Pinpoint Test BD: DTC U3003:16

Instrumentation, Message Center and Warning Chimes

Pinpoint Test BD: DTC U3003:16


Normal Operation

- DTC U3003:16 (Battery Voltage: Circuit Voltage Below Threshold)- sets in the Instrument Panel Cluster (IPC) in continuous memory if the IPC (Instrument Panel Cluster) detects battery voltage below 9 volts on the voltage supply circuit for 5 seconds or longer.

This pinpoint test is intended to diagnose the following:

- Wiring, terminals or connectors

- High circuit resistance

- IPC (Instrument Panel Cluster)

PINPOINT TEST BD : DTC U3003:16

NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector
NOTE:
Failure to disconnect the battery when instructed results in false resistance readings.

BD1 RECHECK THE IPC (Instrument Panel Cluster) DTCs

- Ignition ON.

- Enter the following diagnostic mode on the scan tool: IPC (Instrument Panel Cluster) Self-Test.

- Clear the DTCs.

- Wait 10 seconds.

- Repeat the IPC (Instrument Panel Cluster) self-test.

Is DTC U3003:16 still present?

Yes
GO to BD2.
No
The system is operating correctly at this time. The DTC may have been set due to a previous low battery voltage condition.

BD2 CHECK FOR CHARGING SYSTEM DTCs IN THE PCM

- Enter the following diagnostic mode on the scan tool: PCM Self-Test.

- Carry out the PCM Key ON Engine OFF (KOEO) self-test.

- Retrieve the continuous memory DTCs from all modules.

Are any charging system related DTCs set in the PCM?

Yes
REFER to Charging System.
No
GO to BD3.

BD3 CHECK THE BATTERY CONDITION AND STATE OF CHARGE

- Check the battery condition and verify the battery is fully charged.

Is the battery OK and fully charged?

Yes
GO to BD4.
No
REFER to Battery.

BD4 CHECK THE IPC (Instrument Panel Cluster) VOLTAGE PID

- Ignition ON.

- Measure and record the voltage at the battery.

- Enter the following diagnostic mode on the scan tool: IPC (Instrument Panel Cluster) DataLogger.

- Monitor the IPC (Instrument Panel Cluster) voltage PID (MODULE_VOLT).

Is the voltage within 0.2 volt of the recorded battery voltage?

Yes
GO to BD7.
No
GO to BD5.

BD5 CHECK THE IPC (Instrument Panel Cluster) VOLTAGE SUPPLY

- Ignition OFF.

- Disconnect: IPC (Instrument Panel Cluster) C220.

- Ignition ON.

- Measure the voltage between the IPC (Instrument Panel Cluster) C220-21, circuit SBP11 (BU/RD), harness side and ground.






Is the voltage within 0.2 volt of the recorded battery voltage?

Yes
GO to BD6.
No
REPAIR circuit SBP11 (BU/RD) for high resistance. CLEAR the DTC. REPEAT the self-test.

BD6 CHECK THE IPC (Instrument Panel Cluster) GROUND CIRCUIT

- Ignition OFF.

- Disconnect: Negative Battery Cable.

- Measure the resistance between the IPC (Instrument Panel Cluster) C220-5, circuit GD133 (BK), harness side and ground.






Is the resistance less than 5 ohms?

Yes
GO to BD7.
No
REPAIR circuit GD133 (BK) for high resistance. CLEAR the DTCs. REPEAT the self-test.

BD7 CHECK FOR CORRECT IPC (Instrument Panel Cluster) OPERATION

- Disconnect the IPC (Instrument Panel Cluster) connector.

- Check for:
- corrosion

- damaged pins

- pushed-out pins


- Connect the IPC (Instrument Panel Cluster) connector and make sure it seats correctly.

- Operate the system and verify the concern is still present.

Is the concern still present?

Yes
INSTALL a new IPC (Instrument Panel Cluster). REFER to Instrument Panel Cluster (IPC) . TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.