B2227
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS)
Pinpoint Test AB: DTC B2227
Refer to Wiring Diagrams Set 46, Supplemental Restraint System for schematic and connector information. Electrical Diagrams
Normal Operation
The Restraints Control Module (RCM) continuously monitors the LH front impact severity sensor and circuits for the following faults:
- Open circuit
- Faulted sensor
If a fault is detected, the RCM (Restraints Control Module) will store DTC B2227 in memory and send a message to the Instrument Cluster (IC) module to illuminate the air bag warning indicator.
- DTC B2227 (Front Crash Sensor Driver Communications Fault)- If the RCM (Restraints Control Module) is unable to communicate with the LH front impact severity sensor due to an open circuit or faulted sensor, it will set this DTC.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- LH front impact severity sensor
- RCM (Restraints Control Module)
PINPOINT TEST AB : DTC B2227
WARNING: Always tighten the fasteners of the restraints control module (RCM) and impact sensor (if equipped) to the specified torque. Failure to do so may result in incorrect restraint system operation, which increases the risk of personal injury or death in a crash.
NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.
Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test. Inspection and Verification
NOTE: Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS (Supplemental Restraint System).
NOTE: The SRS (Supplemental Restraint System) must be fully operational and free of faults before releasing the vehicle to the customer.
AB1 RETRIEVE RCM (Restraints Control Module) DTCs
NOTE: All RCM (Restraints Control Module) diagnosis will be carried out using Continuous Memory Diagnostic Trouble Codes (CMDTCs) and status information. Refer to DTC Fault Reporting and Status Information. DTC Fault Reporting and Status Information
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
Does the status information for DTC B2227 indicate a fault was present at the time of request?
Yes
This fault cannot be cleared until it is corrected and the DTC Status information indicates the fault is no longer present.
GO to AB2.
No
This is an intermittent fault. The DTC Status information indicates the fault was not present at time of request. GO to AB5.
AB2 CHECK THE LH FRONT IMPACT SEVERITY SENSOR FOR A FAULT STATUS CHANGE (NO COMMUNICATION INDICATED)
NOTE: This pinpoint test step will attempt to change the fault reported by the RCM (Restraints Control Module) by inducing a different fault condition. If the fault reported changes, this indicates the RCM (Restraints Control Module) is functioning correctly and is not the source of the fault.
- Ignition OFF.
- Depower the system. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: LH Front Impact Severity Sensor C1464.
- Connect a fused jumper wire between LH front impact severity sensor C1464-1, circuit 7-JA49 (YE), harness side and C1464-2, circuit 9-JA49 (BN), harness side.
- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
- DIAGNOSTIC TIP: When viewing DTCs with the impact sensor circuits shorted together, a short to Gnd/Vbatt fault would normally be retrieved.
Does the status information for DTC B2227 indicate a fault was present at the time of request?
Yes
GO to AB3.
No
INSTALL a new LH front impact severity sensor. REFER to Front Impact Severity Sensor . GO to AB6.
AB3 CHECK THE LH FRONT IMPACT SEVERITY SENSOR CIRCUITS FOR AN OPEN
- Ignition OFF.
- Depower the system. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Remove the fused jumper wire between LH front impact severity sensor.
- Disconnect: RCM (Restraints Control Module) C310A and C310B.
- Measure the resistance between RCM (Restraints Control Module) C301A, harness side and LH front impact severity sensor C1464, harness side using the following chart.
RCM (Restraints Control Module) Circuit LH Front Impact Severity Sensor C310A-13 9-JA49 (BN) C1464-2 C310A-14 7-JA49 (YE) C1464-1
Are the resistances less than 0.5 ohm?
Yes
GO to AB4.
No
REPAIR circuit 7-JA49 (YE) or 9-JA49 (BN). GO to AB6.
AB4 CONFIRM THE RCM (Restraints Control Module) FAULT
NOTE: Make sure all restraint system components and the RCM (Restraints Control Module) electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
- Prior to reconnecting any previously disconnected SRS (Supplemental Restraint System) component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- inspect RCM (Restraints Control Module) C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation. Refer to Restraints Control Module (RCM) .
- repair any concerns found.
Refer to Wiring Diagrams Set 5, Connector Repair Procedures for schematic and connector information. Electrical Diagrams
- Connect: RCM (Restraints Control Module) C310A and C310B.
- Connect: LH Front Impact Severity Sensor.
- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
Does the status information for DTC B2227 indicate a fault was present at the time of request?
Yes
INSTALL a new RCM (Restraints Control Module). REFER to Restraints Control Module (RCM) . GO to AB6.
No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to AB5.
AB5 CHECK FOR AN INTERMITTENT FAULT
- Ignition OFF.
- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: LH Front Impact Severity Sensor C1464.
- Disconnect: RCM (Restraints Control Module) C310A and C310B.
- Inspect for the following:
- inspect harness and component connectors for loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- inspect RCM (Restraints Control Module) C310A and C310B CPA (Connector Position Assurance) lever/lock for correct operation. Refer to Restraints Control Module (RCM) .
- repair any concerns found.
Refer to Wiring Diagrams Set 5, Connector Repair Procedures for schematic and connector information. Electrical Diagrams
- Connect: All Previously Disconnected Component(s)/Connector(s).
- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
Does the status information for DTC B2227 indicate a fault was present at the time of request?
Yes
The fault condition is now present. Do not clear any DTCs until all DTC concerns have been resolved.
GO to AB2.
No
The fault is not present and cannot be recreated at this time. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to AB6.
AB6 CHECK FOR ADDITIONAL SRS (Supplemental Restraint System) DTCs
- Ignition OFF.
WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Reconnect all SRS (Supplemental Restraint System) components (if previously disconnected).
- If previously directed to depower the SRS (Supplemental Restraint System), repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- Restraints.
NOTE: When selecting Restraints from the Self Test menu, DTCs will be retrieved from the RCM (Restraints Control Module) and OCSM (Occupant Classification System Module).
- Select the DTC and view DTC Status information.
Does the status information for any RCM (Restraints Control Module) DTC indicate a fault is present and/or are any OCSM (Occupant Classification System Module) on-demand DTCs retrieved?
Yes
Do not clear any DTCs until all DTC concerns have been resolved. GO to the DTC Charts for pinpoint test direction. Air Bag Systems / Seat Belt Systems
No
CLEAR all RCM (Restraints Control Module) and OCSM (Occupant Classification System Module) CMDTCs (Continuous Memory Diagnostic Trouble Codes). PROVE OUT the SRS (Supplemental Restraint System). Repair is complete. RETURN the vehicle to the customer.