C1947
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS)
Pinpoint Test AW: DTC C1947
Refer to Wiring Diagrams Set 46, Supplemental Restraint System for schematic and connector information. Electrical Diagrams
Normal Operation
The Restraints Control Module (RCM) continuously monitors the driver seat track position sensor circuits. If the RCM (Restraints Control Module) detects a fault, it will store DTC C1947 in memory and send a message to the Instrument Cluster (IC) module to illuminate the air bag warning indicator.
- DTC C1947 (Front Driver's Seat Track Position Switch Circuit Short to Ground)- If the RCM (Restraints Control Module) detects a short to ground on the driver seat track position sensor circuit, it will set this DTC.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Faulted driver seat track position sensor
- RCM (Restraints Control Module)
PINPOINT TEST AW : DTC C1947
WARNING: Never probe the electrical connectors on air bag, Safety Canopy(R) or side air curtain modules. Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.
Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test. Inspection and Verification
NOTE: Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS (Supplemental Restraint System).
NOTE: Always make sure the correct SRS (Supplemental Restraint System) component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar.
Check the part number listed in the Ford Catalog Advantage(TM) or equivalent to make sure the correct component is being installed. If an incorrect SRS (Supplemental Restraint System) component is installed, DTCs may set.
NOTE: The SRS (Supplemental Restraint System) must be fully operational and free of faults before releasing the vehicle to the customer.
AW1 RETRIEVE RCM (Restraints Control Module) DTCs
NOTE: All RCM (Restraints Control Module) diagnosis will be carried out using Continuous Memory Diagnostic Trouble Codes (CMDTCs) and status information. Refer to DTC Fault Reporting and Status Information. DTC Fault Reporting and Status Information
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
Does the status information for DTC C1947 indicate a fault was present at the time of request?
Yes
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the self-test. GO to AW2.
No
This is an intermittent fault. The DTC Status information indicates the fault was not present at time of request. GO to AW6.
AW2 CHECK THE DRIVER SEAT TRACK POSITION SENSOR
NOTE: This pinpoint test step will attempt to change the fault reported by the RCM (Restraints Control Module) by inducing a different fault condition. If the fault reported changes, this indicates the RCM (Restraints Control Module) is functioning correctly and is not the source of the fault.
- Ignition OFF.
WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Disconnect: Seat Track Position Sensor C3207.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
- DIAGNOSTIC TIP: When viewing DTCs with the driver seat track position sensor disconnected, an open circuit fault would normally be retrieved.
Does the status information for DTC C1947 indicate a fault was present at the time of request?
Yes
GO to AW3.
No
INSTALL a new driver seat track position sensor. REFER to Seat Position Sensor . GO to AW7.
AW3 CHECK THE DRIVER SEAT TRACK POSITION SENSOR CIRCUIT FOR A SHORT TO GROUND
- Ignition OFF.
- Depower the SRS (Supplemental Restraint System). Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: RCM (Restraints Control Module) C310A and C310B.
- Measure the resistance between driver seat track position sensor C3207-2, circuit 7-JA53 (YE/RD), harness side and ground.
Is the resistance greater than 10,000 ohms?
Yes
GO to AW4.
No
REPAIR circuit 7-JA53 (YE/RD). GO to AW7.
AW4 CHECK FOR A SHORT BETWEEN DRIVER SEAT TRACK POSITION SENSOR CIRCUITS
- Measure the resistance between driver seat track position sensor C3207-2, circuit 7-JA53 (YE/RD), harness side and C3207-1, circuit 9-JA53 (BN/RD), harness side.
Is the resistance greater than 10,000 ohms?
Yes
GO to AW5.
No
REPAIR circuit 7-JA53 (YE/RD) and/or 9-JA53 (BN/RD). GO to AW7.
AW5 CONFIRM THE RCM (Restraints Control Module) FAULT
NOTE: Make sure all restraint system components and the RCM (Restraints Control Module) electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
- Prior to reconnecting any previously disconnected SRS (Supplemental Restraint System) component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- inspect RCM (Restraints Control Module) C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation. Refer to Restraints Control Module (RCM) .
- repair any concerns found.
Refer to Wiring Diagrams Set 5, Connector Repair Procedures for schematic and connector information. Electrical Diagrams
- Connect: RCM (Restraints Control Module) C310A and C310B.
- Connect: Driver Seat Track Position Sensor C3207.
- Repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
Does the status information for DTC C1947 indicate a fault was present at the time of request?
Yes
INSTALL a new RCM (Restraints Control Module). REFER to Restraints Control Module (RCM) . GO to AW7.
No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to AW6.
AW6 CHECK FOR AN INTERMITTENT FAULT
- Ignition OFF.
WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Disconnect driver seat track position sensor C3207:
- inspect connector(s) (including any in-line connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- repair any concerns found.
Refer to Wiring Diagrams Set 5, Connector Repair Procedures for schematic and connector information. Electrical Diagrams
- Connect: All Previously Disconnected Component(s)/Connector(s).
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- RCM (Restraints Control Module).
- Select the DTC and view DTC Status information.
Does the status information for DTC C1947 indicate a fault was present at the time of request?
Yes
The fault condition is now present. Do not clear any DTCs until all DTC concerns have been resolved. GO to AW2.
No
The fault is not present and cannot be recreated at this time. Do not install any new SRS (Supplemental Restraint System) components at this time. SRS (Supplemental Restraint System) components should only be installed when directed to do so in the pinpoint test. GO to AW7.
AW7 CHECK FOR ADDITIONAL SRS (Supplemental Restraint System) DTCs
- Ignition OFF.
WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Reconnect all SRS (Supplemental Restraint System) components (if previously disconnected).
- If previously directed to depower the SRS (Supplemental Restraint System), repower the SRS (Supplemental Restraint System). Do not prove out the SRS (Supplemental Restraint System) at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test- Restraints.
NOTE: When selecting Restraints from the Self Test menu, DTCs will be retrieved from the RCM (Restraints Control Module) and OCSM (Occupant Classification System Module).
Does the status information for any RCM (Restraints Control Module) DTC indicate a fault is present and/or are any OCSM (Occupant Classification System Module) on-demand DTCs retrieved?
Yes
Do not clear any DTCs until all DTC concerns have been resolved. GO to the DTC Charts for pinpoint test direction. Air Bag Systems / Seat Belt Systems
No
CLEAR all RCM (Restraints Control Module) and OCSM (Occupant Classification System Module) CMDTCs (Continuous Memory Diagnostic Trouble Codes). PROVE OUT the SRS (Supplemental Restraint System). Repair is complete. RETURN the vehicle to the customer.