Part 3 of 7

Secondary shaft	Diameter of needle bearing contact area	at 1st gear	Standard or new	39.986 - 39.999 mm
			Service limit	When wore or damaged
		at 2nd gear	Standard or new	39.986 - 39.999 mm
			Service limit	When wore or damaged
	I.D. of gears	1st gear	Standard or new	47.000 - 47.016 mm
			Service limit	When wore or damaged
		2nd gear	Standard or new	46.000 - 46.016 mm
			Service limit	When wore or damaged
	End play of gears	1st gear	Standard or new	0.07 - 0.15 mm
		2nd gear	Standard or new	0.04 - 0.12 mm
	37 x 58 mm thrust washer thickness	No.1	Standard or new	3.900 mm
			Service limit	When wore or damaged
		No.2	Standard or new	3.925 mm
			Service limit	When wore or damaged
		No.3	Standard or new	3.950 mm
			Service limit	When wore or damaged
		No.4	Standard or new	3.975 mm
			Service limit	When wore or damaged
		No.5	Standard or new	4.000 mm
			Service limit	When wore or damaged
		No.6	Standard or new	4.025 mm
			Service limit	When wore or damaged
		No.7	Standard or new	4.050 mm
			Service limit	When wore or damaged
		No.8	Standard or new	4.075 mm
			Service limit	When wore or damaged
		No.9	Standard or new	4.100 mm
			Service limit	When wore or damaged
		No.10	Standard or new	4.125 mm
			Service limit	When wore or damaged
		No.11	Standard or new	4.150 mm
			Service limit	When wore or damaged
		No.12	Standard or new	4.175 mm
			Service limit	When wore or damaged
		No.13	Standard or new	4.200 mm
			Service limit	When wore or damaged
		No.14	Standard or new	4.225 mm
			Service limit	When wore or damaged
		No.15	Standard or new	4.250 mm
			Service limit	When wore or damaged
		No.16	Standard or new	4.275 mm
			Service limit	When wore or damaged
		No.17	Standard or new	4.300 mm
			Service limit	When wore or damaged
		No.18	Standard or new	4.325 mm
			Service limit	When wore or damaged
		No.19	Standard or new	4.350 mm
			Service limit	When wore or damaged
		No.20	Standard or new	4.375 mm
			Service limit	When wore or damaged
	40 x 51.5 mm thrust washer thickness	No.1	Standard or new	4.80 mm
			Service limit	When wore or damaged
		No.2	Standard or new	4.85 mm
			Service limit	When wore or damaged
		No.3	Standard or new	4.90 mm
			Service limit	When wore or damaged
		No.4	Standard or new	4.95 mm
			Service limit	When wore or damaged
		No.5	Standard or new	5.00 mm
			Service limit	When wore or damaged
		No.6	Standard or new	5.05 mm
			Service limit	When wore or damaged
	27 x 45 x 44 mm gear collar length		Standard or new	43.9 - 44.0 mm
	Sealing ring thickness		Standard or new	1.91 - 1.97 mm
			Service limit	1.86 mm
	Width of sealing ring groove		Standard or new	2.025 - 2.060 mm
			Service limit	2.080 mm
	Clutch feed pipe O.D.		Standard or new	7.97 - 7.98 mm
			Service limit	7.95 mm
	Clutch feed pipe bushing O.D.		Standard or new	8.000 - 8.015 mm
			Service limit	8.030 mm
	ATF guide of sealing ring contact I.D.		Standard or new	29.000 - 29.021 mm
			Service limit	29.05 mm