P2183

DTC P2183: ECT Sensor 2 Range/Performance Problem (2005 model)

NOTE: If DTC P0111 is stored at the same time as DTC P2183, troubleshoot DTC P0111 first, then recheck for DTC P2183.

1. Check for poor connections or loose terminals at the ECT sensor 1 and the ECT sensor 2.

Are the connections and terminals OK?

YES - Go to step 2.

NO - Repair the connectors or terminals, then go to step 27.

2. Turn the ignition switch ON (II).
3. Check for Temporary DTCs or DTCs with the HDS.

Are DTC P1116 and P2183 indicated at the same time?

YES - Go to step 15.

NO - Go to step 4.

4. Start the engine, and let it idle for 10 minutes.
5. Check the ECT SENSOR 2 in the DATA LIST with the HDS.

Is about 131 °F (55 °C) or less, or 1.50 V or higher indicated?

YES - Replace the ECT sensor 2, then go to step 27.

NO - Go to step 6.

6. Turn the ignition switch OFF.
7. Drain the coolant.
8. Remove the ECT sensor 2.
9. Allow the ECT sensor 2 to cool to 77 °F (25 °C).
10. Note the outside temperature.
11. Connect the ECT sensor 2 to the 2P connector, but do not install them in the engine.
12. Turn the ignition switch ON (II).
13. Note the value of ECT SENSOR 2 quickly in the DATA LIST with the HDS.
14. Compare the value of ECT SENSOR 2 and the outside temperature.

Does ECT SENSOR 2 differ 5.4 °F (3 °C) or more?

YES - Replace the ECT sensor 2, then go to step 27.

NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the ECT sensor 1, the ECT sensor 2, and the ECM/PCM.

15. Start the engine, and let it idle for 10 minutes.
16. Check the ECT SENSOR 1 in the DATA LIST with the HDS.

Is about 118 °F (48 °C) or less, or 1.75 V or higher indicated?

YES - Replace the ECT sensor 1, then go to step 27.

NO - Go to step 17.

17. Let the engine idle for 10 minutes.
18. Check the ECT SENSOR 2 in the DATA LIST with the HDS.

Is about 131 °F (55 °C) or less, or 1.50 V or higher indicated?

YES - Replace the ECT sensor 2, then go to step 27.

NO - Go to step 19.

19. Turn the ignition switch OFF.
20. Drain the coolant.
21. Remove the ECT sensor 1 and the ECT sensor 2.
22. Allow the sensors to cool to 77 °F (25 °C).
23. Note the outside temperature.
24. Connect ECT sensor 1 to the 2P connector, and ECT sensor 2 to the 2P connector, but do not install them in the engine.
25. Note the value of ECT SENSOR 1 and ECT SENSOR 2 quickly in the DATA LIST with the HDS.
26. Compare the value of ECT SENSOR 1 and the outside temperature, and the value of ECT SENSOR 2 and the outside temperature individually.

Does either sensor differ more than 5.4 °F (3 °C) from the outside temperature?

YES - Replace the sensor that differed more than 5.4 °F (3 °C) from the outside temperature, then go to step 27.

NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the ECT sensor 1, the ECT sensor 2, and the ECM/PCM.

27. Turn the ignition switch ON (II).
28. Reset the ECM/PCM with the HDS.
29. Do the ECM/PCM idle learn procedure. Programming and Relearning
30. Check for Temporary DTCs or DTCs with the HDS.

Are any Temporary DTCs or DTCs Indicated?

YES - If DTC P2183 is indicated, check for poor connections or loose terminals at the ECT sensor 1, the ECT sensor 2, and the ECM/PCM then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.

NO - Troubleshooting is complete.