Operation CHARM: Car repair manuals for everyone.
Home >> Honda >> 2009 >> CR-V 2WD L4-2.4L >> Repair and Diagnosis >> Body and Frame >> Seats >> Seat Cover >> Service and Repair >> Front Seat-Back Cover/Pad Replacement
Manuals through 2025 now available!

Our trusted friends have launched a new website named LEMON, which has newer manuals. It also contains all the CHARM manuals.

LEMON is the spiritual successor to CHARM, I recommend you try it!

Link: lemon-manuals.la or lemon-manuals.org.ua

(Some people have issue connecting. LEMON is investigating. For now, use Firefox or change your DNS server)

Or, hide this message: temporarily or permanently

Front Seat-Back Cover/Pad Replacement




Front Seat-back Cover/Pad Replacement

SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Technician Safety Information before doing repairs or service.

- Check the operation of the driver's seat position sensor after any of these actions: Drivers Seat Position Sensor Operation Check
- Driver's seat position sensor replacement

- Cover plate (front side of driver's seat slide rail) replacement

- Calibrate the ODS unit after any of these actions: Programming and Relearning
- Front passenger's seat replacement (including any seat components)

- Replacement of the seat weight sensors

- After a vehicle collision

NOTE:

- Take care not to tear the seams or damage the seat covers.

- On the passenger's seat, do not touch the ODS sensor in the seat-back pad, and keep it away from oil.
Oil can corrode the sensor causing it to fail.

- Put on gloves to protect your hands.

1. Remove the front seat. Front Seat Removal/Installation

2. Passenger's seat: Remove the front seat under tray. Front Seat Under Tray Replacement

3. Remove the armrest. Front Seat Armrest Replacement

4. Remove the head restraint.

5. From under the seat cushion, detach the side airbag connector clip (A) and the seat heater connector clip (driver's seat) (B), then remove the wire harness ties (C).

6. Release the hook (D) or strap (E) and the slits in the seat cushion cover (F) from the seat cushion frame springs (G), then pull the cover back.

Passenger's seat





Driver's seat (manual seat)





Driver's seat (8-way power seat)





7. Using the appropriate trim tool, pry out the clips (A) to release the lower portion of the back cover.

8. Detach the clips and the hooks (B) by pulling the bottom of the back cover (C) back, then gently pull down the cover to release the hooks (D) from the seat frame, and remove the panel.






9. Release the Velcro fasteners (A) and the hooks (B), then pull the seat-back cover (C) back.

Manual seat





8-way power seat





10. Pull the side airbag harness (A) out through the harness holes (B) in the seat-back cover and the seat frame. Disconnect the seat-back heater harness connector (C) if equipped. Driver's seat is shown; passenger's seat is similar.

11. Remove the side airbag. Side Airbag Replacement

Manual seat





8-way power seat





12. Release the hook strips (A), then loosen the seat-back cover (B). Driver's seat is shown; passenger's seat is similar.

Manual seat





8-way power seat





13. Turn over the reinforcing cloth (A), then release the hooks (B) from the side airbag module holder (C). Passenger's seat is shown; driver's seat is symmetrical.






14. Passenger's seat: Disconnect the OPDS sensor connectors (A) and the ODS subharness connector (B) from the ODS unit (C), and pull them in through the hole in the seat frame. Detach the harness clips (D), and remove the wire harness.






15. Pinch the tabs on the ends of the head restraint guides (A), and remove them from the seat-back.






16. Remove the seat-back cover/pad (A) from the seat (B).






17. Pull back the edge of the seat-back cover all the way around, and release the clips (A), then remove the seat-back cover.






18. Install the cover in the reverse order of removal, and note these items:
- Reinitialize the ODS unit. Programming and Relearning

- To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly over the pad before securing the clips, the hooks, and the hook strips.

- Replace any clips (A) you removed with new ones.

- Before installing the side airbag (B), make sure the reinforcing cloth (C) is fixed on the seat-back frame (D) securely.

- Make sure the side airbag harness and ODS subharness (passenger's seat) are routed properly.









pro multis · About Operation CHARM