Campaign TC9 - ECM Software Update
Group CAMPAIGNNumber 10-01-036
Date OCTOBER, 2010
Model
2011 TUCSON (LM) 2.4L
Subject
AUTOMATIC TRANSMISSION TCM UPDATE (SERVICE CAMPAIGN TC9)
******DEALER STOCK ONLY******
IMPORTANT:
DEALERS MUST PERFORM THIS CAMPAIGN ON ALL AFFECTED VEHICLES PRIOR TO CUSTOMER RETAIL DELIVERY.
IMPORTANT:
WHEN A VEHICLE ARRIVES AT THE SERVICE DEPARTMENT, ACCESS HYUNDAI MOTOR AMERICA'S "WARRANTY VEHICLE INFORMATION" SCREEN VIA WEBDCS TO IDENTIFY OPEN CAMPAIGNS.
DESCRIPTION:
This bulletin provides a procedure to update the TCM for 2011 Tucson 2.4L vehicles with automatic transaxles.
APPLICABLE VEHICLES:
Model: 2011 Tucson 2.4L (LM) vehicles with automatic transaxles
Production date range: From beginning of production through October 11, 2010
ROM ID INFORMATION TABLE:
Verify the TCM ROM ID before attempting to update the vehicles software. Refer to the ROM ID Information Table below:
INTERNET UPDATE
Confirm your GDS has the most recent version. If not, connect the GDS to an internet port, open the GDS home page and select "Internet Update". See the instructions on hmaservice.com, if necessary.
GDS SYSTEM AND TCM UPDATE PRECAUTIONS:
WARNING:
Make sure that the battery symbol indicator at the bottom right tray of the GDS laptop shows at least 50%; if not, charge the GDS or attach a battery charger.
^ Connect the USB cable (A) between the GDS and the VCI.
NOTE:
The USB cable is necessary because wireless communication is not available for the update.
^ Connect the 16-pin DLC connector from the VCI into the DLC located under the driver's side dash.
^ Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories (including heater/air conditioner/blower, radio, heated seats, rear defroster, etc.) to make certain the battery will not be discharged during reprogramming.
^ Perform update with the ignition key in the ON position.
^ Be careful not to disconnect any cables connected to the vehicle or the GDS during reprogramming.
^ Do not start the engine or turn the ignition switch OFF during reprogramming.
NOTE:
Call GIT for GDS technical support issues.
1-1. AUTO MODE TCM UPDATE PROCEDURE
1. From the GDS Home page, select ECU Upgrade. If necessary, select the VIN manually.
2. Select AT as the system and select OK.
3. Select Auto Mode and select Next.
4. From the System tab, select AT and click OK. The GDS will read the ROM ID.
5. Update event 212 LM TCM Upgrade will display. Confirm the ROM is applicable, "ROM ID Information" above. Select Upgrade.
6. If the screen indicates "Voltage is OK", select OK. If not, select CANCEL and charge the vehicle battery.
7. The progress bar will indicate when reprogramming reaches 100%. Wait until the next screen indicates reprogramming is complete.
8. The GDS will confirm that TCM reprogramming is successfully finished. Turn the ignition switch off for at least 10 seconds then turn back ON. Click OK. If not successful, go to, 1-2. MANUAL TCM UPDATE PROCEDURE.
9. Check for Diagnostic Trouble Codes and erase any DTC present.
10. Reset the TCM adaptive learning values using the GDS "Option Treatment" menu on the main screen.
11. Start the engine to confirm proper operation.
1-2. MANUAL MODE TCM UPDATE PROCEDURE:
^ The manual update should be performed only if the automatic update fails.
^ If automatic update falls, disconnect the ECM connectors for 10 minutes and then reconnect them before performing the manual update.
1. From the GDS home screen, select ECU Upgrade. If necessary, select the VIN.
2. Select Manual Mode and click Next.
3. From the System tab, select AT and click Next.
4. Upgrade Event 212 LM TCM Upgrade will display. Select Next.
5. The ROM ID will display. Select Upgrade.
6. Refer to the table below and select the password. Click OK.
7. If the results indicate "Voltage is OK", select OK. If not, select CANCEL and charge the vehicle battery.
8. The progress bar will indicate when reprogramming reaches 100%. Wait until the next screen indicates reprogramming is complete.
9. The GDS will confirm that TCU reprogramming is successfully finished. Turn the ignition key OFF for 10 seconds and click OK.
10. Check for Diagnostic Trouble Codes (DTCs) and erase any DTC(s) present.
11. Reset the TCM adaptive learning values using the GDS "Option Treatment" menu.
12. Start the engine to confirm proper operation.
WARRANTY INFORMATION
NOTE:
Enter claim on Campaign Claim Entry Screen