Operation CHARM: Car repair manuals for everyone.
Home >> Lexus >> 2004 >> RX 330 AWD V6-3.3L (3MZ-FE) >> Repair and Diagnosis >> Restraints and Safety Systems >> Seat Belt Systems >> Seat Belt >> Service and Repair >> Removal and Installation >> Rear Seat Belt

Rear Seat Belt

REPLACEMENT

HINT:
- The installation is in the reverse order of the removal.However, when there is a special point concerning the installation, it is indicated.
- Use the same procedures on the LH side as on the RH side.

1. REMOVE REAR SEAT ASSY RH
2. REMOVE REAR SEAT ASSY LH
3. REMOVE REAR DOOR SCUFF PLATE RH
4. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
5. REMOVE DECK BOARD SUB-ASSY
6. REMOVE TONNEAU COVER ASSY
7. REMOVE DECK FLOOR BOX FRONT
8. REMOVE DECK FLOOR BOX REAR
9. REMOVE DECK BOARD SUB-ASSY NO.2
10. REMOVE DECK BOARD SUB-ASSY NO.3
11. REMOVE BACK DOOR WEATHERSTRIP
12. REMOVE REAR FLOOR FINISH PLATE
13. REMOVE DECK SIDE TRIM BOX RH
14. REMOVE REAR FLOOR FINISH SIDE PLATE RH
15. REMOVE DECK SIDE TRIM COVER RH
16. REMOVE REAR SEAT SIDE COVER RH
17. REMOVE ROPE HOOK
18. REMOVE DECK TRIM SIDE PANEL ASSY RH
19. REMOVE ROOM LAMP ASSY NO.2
20. REMOVE ROOF SIDE GARNISH ASSY INNER RH
21. REMOVE REAR NO.1 SEAT BELT ASSY OUTER RH
a. Remove the nut and seat belt on the shoulder anchor side.
b. Remove the 2 bolts on the retractor side, and remove the seat belt completely.

22. REMOVE REAR SEAT BELT ASSY OUTER CENTER (REAR SEAT ASSY RH)
a. Remove the seatback board.
b. Remove the shoulder belt cover.
c. Remove the bolt and belt on the floor anchor side.
d. Remove the bolt and nut on the retractor side, and remove the belt completely.

23. REMOVE REAR SEAT BELT ASSY INNER (REAR SEAT ASSY RH)
a. Remove the bolt and seat belt.

24. REMOVE REAR SEAT BELT ASSY INNER (REAR SEAT ASSY RH)
a. Remove the nut and seat belt.

25. REMOVE REAR SEAT BELT ASSY INNER (REAR SEAT ASSY LH)
a. Remove the bolt and seat belt.

26. INSTALL REAR SEAT BELT ASSY INNER (REAR SEAT ASSY LH)
a. Install the seat belt with the bolt.

Torque: 42 Nm (430 kgf.cm, 31 ft.lbf)




27. INSTALL REAR SEAT BELT ASSY OUTER CENTER (REAR SEAT ASSY RH)
a. Install the belt on the retractor side with the bolt and nut.

Torque:
7.5 Nm (76.5 kgf.cm, 75 in.lbf) for upper bolt
42 Nm (430 kgf.cm, 31 ft.lbf) for lower nut

b. Install the shoulder belt cover.
c. Install the seatback board center.
d. Check the degree of tilt when the belt begins to lock the ELR.

NOTE: Do not disassemble the retractor.

1. Check that the belt does not lock within 15 ° of tilt in all directions but that the belt locks with over 45 ° of tilt, when gently moving the retractor.
If operation is not as specified, replace the belt assy.

e. Install the belt with the bolt.

Torque: 42 Nm (430 kgf.cm, 31 ft.lbf)

f. Check the ELR lock.

NOTE: The check should be performed with the assembly installed.

1. Check that the belt locks when pulling out the belt quickly when the belt is installed.

HINT: The seat belt does not lock when the pull-out amount of the belt is 955 mm (37.60 in.) or less.
If operation is not as specified, replace the belt assy.

g. Check the fastening function of the child restraint system.

NOTE: The check should be performed with the assembly installed.

1. Check that the belt can not be pulled out any more but can rewind after it is fully pulled out.
2. Check that the belt can be pulled out and can rewind after it is fully rewound.
If operation is not as specified, replace the belt assy.




28. INSTALL REAR SEAT BELT ASSY INNER (REAR SEAT ASSY RH)
a. Install the floor anchor and belt with the nut, as shown in the illustration.

Torque: 42 Nm (430 kgf.cm, 31 ft.lbf)

NOTE: Do not make the anchor part run onto the protrusion part of the floor panel.

29. INSTALL REAR SEAT BELT ASSY INNER (REAR SEAT ASSY RH)
a. Install the seat belt with the bolt.

Torque: 42 Nm (430 kgf.cm, 31 ft.lbf)

30. INSTALL REAR NO.1 SEAT BELT ASSY OUTER RH
a. Install the belt with the 2 nuts on the retractor side.

Torque: 42 Nm (430 kgf.cm, 31 ft.lbf)




b. Check the degree of tilt when the belt begins to lock the ELR.

NOTE: Do not disassemble the retractor.

1. Check that the belt does not lock within 15 ° of tilt in all directions but that the belt locks with over 45 ° of tilt, when gently moving the retractor.
If operation is not as specified, replace the belt assy.




c. Install the belt with the bolt on the floor anchor side.

Torque: 42 Nm (430 kgf.cm, 31 ft.lbf)

NOTE: Do not make the anchor part run onto the protrusion part of the floor panel.

1. Check that the belt locks when pulling out the belt quickly when the belt is installed.
If operation is not as specified, replace the seat belt assy.

d. Check the ELR lock.

NOTE: The check should be performed with the assembly installed.

1. Check that the belt locks when pulling out the belt quickly when the belt is installed.
If operation is not as specified, replace the belt assy.

e. Check the fastening function of the child restraint system.

NOTE: The check should be performed with the assembly installed.

1. Check that the belt can not be pulled out any more but rewind after being pulled out fully.
2. Check that the belt can be pulled out and rewound after the belt has been fully rewound.
If operation is not as specified, replace the belt assy.

31. INSTALL REAR SEAT ASSY LH
32. INSTALL REAR SEAT ASSY RH
pro multis · About Operation CHARM