Headliner: Service and Repair
REPLACEMENTHINT: Installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated.
1. REMOVE REAR NO.2 SEAT ASSEMBLY LH
2. REMOVE REAR NO.2 SEAT ASSEMBLY RH
3. REMOVE FRONT DOOR SCUFF PLATE LH
a. Using a screwdriver, disengage the 6 claws and remove the scuff plate.
HINT: Tape the screwdriver tip before use.
4. REMOVE FRONT DOOR SCUFF PLATE RH
HINT: Use the same procedures described above for the LH side.
5. REMOVE COWL SIDE TRIM BOARD LH
a. Remove the cap nut.
b. Using a screwdriver, disengage the 2 claws and remove the trim board.
HINT: Tape the screwdriver tip before use.
6. REMOVE COWL SIDE TRIM BOARD RH
HINT: Use the same procedures described above for the LH side.
7. REMOVE QUARTER SCUFF PLATE INSIDE LH
a. Remove the 2 quarter scuff plate inner covers.
b. Using a screwdriver, disengage the 4 claws and remove the scuff plate.
HINT: Tape the screwdriver tip before use.
8. REMOVE QUARTER SCUFF PLATE INNER RH
HINT: Use the same procedures described above for the LH side.
9. REMOVE REAR DOOR SCUFF PLATE LH
a. Using a screwdriver, disengage the 4 claws and remove the scuff plate.
10. REMOVE REAR DOOR SCUFF PLATE RH
HINT: Use the same procedures described above for the LH side.
11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
13. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
15. REMOVE CENTER PILLAR GARNISH LOWER LH
a. Remove the front seat belt anchor bolt and front seat belt.
b. Disengage the 2 clips and 2 claws, and remove the center pillar garnish.
16. REMOVE CENTER PILLAR GARNISH LOWER RH
HINT: Use the same procedures described above for the LH side.
17. REMOVE CENTER PILLAR GARNISH LH
a. Remove the 2 screws.
b. Disengage the 2 claws and clip, and remove the pillar garnish.
18. REMOVE CENTER PILLAR GARNISH RH
HINT: Use the same procedures described above for the LH side.
19. REMOVE BACK DOOR WEATHERSTRIP
20. REMOVE REAR FLOOR MAT SUPPORT PLATE REAR
a. Remove the 5 screws.
b. Using a screwdriver, disengage the 2 claws and remove the mat support plate.
HINT: Tape the screwdriver tip before use.
21. REMOVE QUARTER INSIDE TRIM BOARD LH
a. Remove the bolt and the floor anchor part of the rear No. 1 seat belt assembly.
b. Remove the 3 screws.
c. Using a screwdriver, disengage the 8 clips and remove the trim board.
HINT: Tape the screwdriver tip before use.
22. REMOVE QUARTER INSIDE TRIM BOARD RH
HINT: Use the same procedures described above for the LH side.
23. REMOVE ROOF SIDE GARNISH INNER LH
a. Remove the floor anchor part of the seat No. 2 belt assembly.
b. Using a screwdriver, firmly push the pin to disengage the clips (A).
HINT: Tape the screwdriver tip before use.
c. Using a screwdriver, disengage the 8 clips (B and C) and remove the garnish.
HINT:
- Tape the screwdriver tip before use.
- The clip (A) cannot be reused.
24. REMOVE ROOF SIDE GARNISH INNER RH
HINT: Use the same procedures described above for the LH side.
25. REMOVE FRONT PILLAR GARNISH LH
a. Remove the 2 grip plugs, 2 screws and assist grip.
b. Using a screwdriver, disengage the clip and remove the garnish.
HINT: Tape the screwdriver tip before use.
c. Pull the garnish upward, and remove the pillar garnish from the instrument panel.
d. w/ Curtain shield airbag:
Protect the curtain shield airbag.
1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.
NOTE: Cover the curtain shield airbag with the protection cover as soon as the front pillar garnish is removed.
26. REMOVE FRONT PILLAR GARNISH RH
HINT: Use the same procedures described above for the LH side.
27. REMOVE ASSIST GRIP ASSEMBLY
a. Using a screwdriver, disengage the 6 claws and remove the 2 assist grip plugs.
HINT: Tape the screwdriver tip before use.
b. Remove the 2 screws and assist grip.
28. REMOVE TELEVISION BASE (W/ RR TELEVISION)
29. REMOVE ROOF CONSOLE BOX SUB-ASSEMBLY
a. Using a screwdriver, disengage the 3 claws and 2 clips, and remove the console box assembly.
HINT: Tape the screwdriver tip before use.
b. Disconnect the map lamp switch connector and sliding roof switch connector.
30. REMOVE ROOM LAMP ASSEMBLY N0.1
a. Using a screwdriver, remove the lens cover.
b. Using a screwdriver, disengage the 4 claws and remove the room lamp assembly, as shown in the illustration.
HINT: Tape the screwdriver tip before use.
c. Disconnect the room lamp connector.
31. REMOVE ROOM LAMP ASSEMBLY N0.2
a. Using a screwdriver, remove the lens cover.
b. Using a screwdriver, disengage the 4 claws and remove the room lamp assembly, as shown in the illustration.
HINT: Tape the screwdriver tip before use.
c. Disconnect the room lamp connector.
32. REMOVE ROOF HEADLINING REAR TRIM COVER LH
a. Pull out the seat belt buckle from the roof headlining trim cover.
b. Using a roof moulding remover, disengage the 6 claws and remove the roof headlining trim cover.
33. REMOVE VISOR BRACKET COVER
a. Remove the 2 screws and center visor.
b. Using a screwdriver, disengage the 4 claws and remove the visor bracket cover.
HINT: Tape the screwdriver tip before use.
34. REMOVE LH VISOR ASSEMBLY
a. Remove the 2 screws and visor assembly.
35. REMOVE RH VISOR ASSEMBLY
a. Remove the 2 screws and visor assembly.
36. REMOVE VISOR HOLDER
a. Remove the screws and visor holders.
37. REMOVE ROOF HEADLINING ASSEMBLY
38. REMOVE ROOF SIDE AIR OUTLET REGISTER
a. Remove the screw and register.
39. INSTALL ROOF HEADLINING ASSEMBLY
a. Attach double-sided tape along the markings on the roof panel, as shown in the illustration.
HINT: Be careful that dirt or foreign object does not stick to the adhesive part when removing the peeling paper from the double-sided tape.
b. Attach the roof wire harness across the adhesive part.
NOTE: Attach roof wire harness securely.
40. INSTALL ROOF SIDE GARNISH INNER LH
a. Install the clip (A) in the pin on the garnish side.
b. Engage the claws and 8 clips.
c. Install the floor anchor part of the rear seat No.2 belt assembly.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
41. INSTALL ROOF SIDE GARNISH INNER RH
HINT:
a. Use the same procedures described above for the LH side.
42. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH
43. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH
44. INSTALL REAR SEAT BELT ASSEMBLY OUTER
45. INSTALL REAR SEAT BELT ASSEMBLY OUTER
46. INSTALL REAR NO.2 SEAT ASSEMBLY LH
47. INSTALL REAR NO.2 SEAT ASSEMBLY RH