DTC B0029[1B] Driver Curtain Airbag Circuit High Resistance (Air Bag (Driver/Passenger/Side/Roof/Knee/Far Side))

1. SRS system check

Refer to "58.SRS Control 8A.Troubleshooting(Air Bag (Driver/Passenger/Side/Roof/Knee/Far Side)) diagnostic system check-SRS controls".

2. Driver curtain airbag circuit resistance check

1) Observe the Driver Curtain Airbag Loop Resistance parameter on the scan tool. Is the Driver Curtain Airbag Loop Resistance parameter more than or equal to the specified value?

Value: 7 Ω

Yes

=>Go to Driver curtain airbag harness connector connection verification.

Go to Intermittent conditions of SRS control.

Refer to "209.Restraints 22D.Symptom Intermittent conditions of SRS control".

3. Driver curtain airbag harness connector connection verification

1) Verify that the driver curtain airbag harness connector (R28) is securely connected. Is the driver curtain airbag harness connector (R28) securely connected?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Driver curtain airbag harness connector inspection.

Securely connect the driver curtain airbag harness connector (R28).

=>Go to Repair verification.

4. Driver curtain airbag harness connector inspection

1) Disconnect the driver curtain airbag harness connector (R28).

2) Inspect the driver curtain airbag harness connector terminals (pins 1 and 2 of R28) for bending, dirt, etc. Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Current DTC check.

Repair the connections as necessary.

=>Go to Repair verification.

5. Current DTC check

1) Connect the driver curtain airbag harness connector (R28).

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

2) Turn ON the ignition switch.

3) Observe the DTC information with a scan tool for DTC B0029[1B] being set as a current failure. Is a DTC set?

Yes

=>Go to Driver curtain airbag circuit check.

=>Go to Repair verification.

6. Driver curtain airbag circuit check

1) Turn OFF the ignition switch for 15 seconds or more.

2) Disconnect the driver curtain airbag harness connector (R28).

3) Connect the SRS alternative load and the appropriate adapter from the adapter harness kit to the driver curtain airbag harness connector (R28).

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

SST: 5-8840-2857-0 - adapter harness kit

SST: 5-8840-2856-0 - SRS alternative load

4) Turn ON the ignition switch.

5) Observe the DTC information with a scan tool for DTC B0029[1B] being set as a current failure. Is a DTC set?

Yes

=>Go to Inspection for open circuit in driver curtain airbag deployment current output (High) circuit.

Replace the driver curtain airbag.

Refer to "8.Restraints 8B.Airbag Systems curtain airbag removal".

Refer to "8.Restraints 8B.Airbag Systems curtain airbag installation".

=>Go to Repair verification.

7. Inspection for open circuit in driver curtain airbag deployment current output (High) circuit

1) Turn OFF the ignition switch for 15 seconds or more.

2) Inspect the driver curtain airbag deployment current output (High) circuit between the SRS control unit (pin 2 of R6) and the driver curtain airbag (pin 1 of R28) for an open circuit or high resistance. Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Inspection for open circuit in driver curtain airbag deployment current output (Low) circuit.

Repair the circuit as necessary.

=>Go to Repair verification.

8. Inspection for open circuit in driver curtain airbag deployment current output (Low) circuit

1) Inspect the driver curtain airbag deployment current output (Low) circuit between the SRS control unit (pin 1 of R6) and the driver curtain airbag (pin 2 of R28) for an open circuit or high resistance. Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to SRS control unit harness connector inspection.

Repair the circuit as necessary.

=>Go to Repair verification.

9. SRS control unit harness connector inspection

1) Inspect for poor connections at the SRS control unit harness connector (pins 1 and 2 of R6). Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to SRS control unit replacement.

Repair the connections as necessary.

=>Go to Repair verification.

10. SRS control unit replacement

Note

Perform the VIN programming and ECU lock after replacing the SRS control unit.

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit removal".

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit installation".

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit setting".

Procedure completion

=>Go to Repair verification.

11. Repair verification

1) Reconnect all of the disconnected harness connectors.

2) Clear the DTC with a scan tool.

3) Turn OFF the ignition switch for 15 seconds or more.

4) Turn ON the ignition switch.

5) Observe the DTC information with a scan tool.