1. SRS system check
2. Current DTC check
1) Clear the DTC with a scan tool.
2) Turn OFF the ignition switch for 15 seconds or more.
3) Turn ON the ignition switch.
4) Observe the DTC information with a scan tool for DTC B0020[11] being set as a current failure. Is a DTC set?
Yes
=>Go to Passenger side airbag circuit check.
No
Go to Intermittent conditions of SRS control.
Refer to "209.Restraints 22D.Symptom Intermittent conditions of SRS control".
3. Passenger side airbag circuit check
1) Turn OFF the ignition switch for 15 seconds or more.
2) Disconnect the passenger side airbag harness connector (R9).
3) Connect the SRS alternative load and the appropriate adapter from the adapter harness kit to the passenger side airbag harness connector (R9).
Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).
SST: 5-8840-3258-0 - SRS adapter for load tool
SST: 5-8840-2856-0 - SRS alternative load
4) Turn ON the ignition switch.
5) Observe the DTC information with a scan tool for DTC B0020[11] being set as a current failure. Is a DTC set?
Yes
No
Replace the passenger side airbag.
Refer to "8.Restraints 8B.Airbag Systems side airbag removal".
Refer to "8.Restraints 8B.Airbag Systems side airbag installation".
4. Inspection for short to ground in passenger side airbag deployment current output (High) circuit
1) Turn OFF the ignition switch for 15 seconds or more.
2) Inspect the passenger side airbag deployment current output (High) circuit between the SRS control unit (pin 15 of R7) and the passenger side airbag (pin 1 of R9) for a short to ground. Is the result normal?
Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Yes
No
Repair the circuit as necessary.
5. Inspection for short circuit in passenger side airbag deployment current output (Low) circuit
1) Inspect the passenger side airbag deployment current output (Low) circuit between the SRS control unit (pin 16 of R7) and the passenger side airbag (pin 2 of R9) for a short to ground. Is the result normal?
Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Yes
=>Go to SRS control unit replacement.
No
Repair the circuit as necessary.
6. SRS control unit replacement
Note
- Perform the VIN programming and ECU lock after replacing the SRS control unit.
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit removal".
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit installation".
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit setting".
Procedure completion
7. Repair verification
1) Reconnect all of the disconnected harness connectors.
2) Clear the DTC with a scan tool.
3) Turn OFF the ignition switch for 15 seconds or more.
4) Turn ON the ignition switch.
5) Observe the DTC information with a scan tool.