DTC B0020[1A] Passenger Side Airbag Circuit Low Resistance (Air Bag (Driver/Passenger/Side/Roof/Knee/Far Side))

1. SRS system check

Refer to "58.SRS Control 8A.Troubleshooting(Air Bag (Driver/Passenger/Side/Roof/Knee/Far Side)) diagnostic system check-SRS controls".

2. Passenger side airbag circuit resistance check

1) Observe the Passenger Side Airbag Loop Resistance parameter on the scan tool. Is the Passenger Side Airbag Loop Resistance parameter less than or equal to the specified value?

Value: 1 Ω

Yes

=>Go to Passenger side airbag harness connector connection verification.

No

Go to Intermittent conditions of SRS control.

Refer to "209.Restraints 22D.Symptom Intermittent conditions of SRS control".

3. Passenger side airbag harness connector connection verification

1) Verify that the passenger side airbag harness connector (R9) is securely connected. Is the passenger side airbag harness connector (R9) securely connected?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Passenger side airbag harness connector inspection.

No

Securely connect the passenger side airbag harness connector (R9).

=>Go to Repair verification.

4. Passenger side airbag harness connector inspection

1) Disconnect the passenger side airbag harness connector (R9).

2) Inspect the passenger side airbag harness connector terminals (pins 1 and 2 of R9) for bending, dirt, etc. Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Current DTC check.

No

Repair the connections as necessary.

=>Go to Repair verification.

5. Current DTC check

1) Connect the passenger side airbag harness connector (R9).

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

2) Turn ON the ignition switch.

3) Observe the DTC information with a scan tool for DTC B0020[1A] being set as a current failure. Is a DTC set?

Yes

=>Go to Passenger side airbag circuit check.

No

=>Go to Repair verification.

6. Passenger side airbag circuit check

1) Turn OFF the ignition switch for 15 seconds or more.

2) Disconnect the passenger side airbag harness connector (R9).

3) Connect the SRS alternative load and the appropriate adapter from the adapter harness kit to the passenger side airbag harness connector (R9).

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

SST: 5-8840-3258-0 - SRS adapter for load tool

SST: 5-8840-2856-0 - SRS alternative load

4) Turn ON the ignition switch.

5) Observe the DTC information with a scan tool for DTC B0020[1A] being set as a current failure. Is a DTC set?

Yes

=>Go to Inspection for short circuit in passenger side airbag circuit.

No

Replace the passenger side airbag.

Refer to "8.Restraints 8B.Airbag Systems side airbag removal".

Refer to "8.Restraints 8B.Airbag Systems side airbag installation".

=>Go to Repair verification.

7. Inspection for short circuit in passenger side airbag circuit

1) Turn OFF the ignition switch for 15 seconds or more.

2) Inspect for a short together between the passenger side airbag deployment current output (High) circuit and the passenger side airbag deployment current output (Low) circuit between the SRS control unit (pins 15 and 16 of R7) and the passenger side airbag (pins 1 and 2 of R9). Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to SRS control unit replacement.

No

Repair the circuit as necessary.

=>Go to Repair verification.

8. SRS control unit replacement

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit removal".

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit installation".

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit setting".

Procedure completion

=>Go to Repair verification.

9. Repair verification

1) Reconnect all of the disconnected harness connectors.

2) Clear the DTC with a scan tool.

3) Turn OFF the ignition switch for 15 seconds or more.

4) Turn ON the ignition switch.

5) Observe the DTC information with a scan tool.