1) Check whether any aftermarket electronic equipment is installed. Is any aftermarket electronic equipment installed?
Yes
No
=>Go to Inspection for short circuit in left side front airbag sensor (+) circuit.
1) Connect the scan tool.
2) Turn OFF the ignition switch for 15 seconds or more.
3) Turn OFF the power of all aftermarket electronic equipment.
4) Perform a test drive.
5) Observe the DTC information with a scan tool for DTC B0090[09] being set as a current failure. Is a DTC set?
Yes
=>Go to Inspection for short circuit in left side front airbag sensor (+) circuit.
No
Explain to the customer that aftermarket electronic equipment may be the cause of the defect and remove the aftermarket electronic equipment.
1) Turn OFF the ignition switch for 15 seconds or more.
2) Disconnect the left side front airbag sensor harness connector (C23) and SRS control unit harness connector (B9).
3) Inspect the left side front airbag sensor (+) circuit between the SRS control unit (pin 12 of B9) and the left side front airbag sensor (pin 2 of C23) for a short to another circuit. Is the result normal?
Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Yes
=>Go to Inspection for short circuit in left side front airbag sensor (-) circuit.
No
Repair the circuit as necessary.
1) Inspect the left side front airbag sensor (-) circuit between the SRS control unit (pin 20 of B9) and the left side front airbag sensor (pin 1 of C23) for a short to another circuit. Is the result normal?
Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Yes
=>Go to Left side front airbag sensor harness connector inspection.
No
Repair the circuit as necessary.
1) Inspect for poor connections at the left side front airbag sensor harness connector (pins 1 and 2 of C23). Is the result normal?
Refer to "LHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD SRS airbag (Driver/Passenger/Side/Curtain/Knee/Far Side)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Yes
Replace the left side front airbag sensor.
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control front airbag sensor removal".
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control front airbag sensor installation".
No
Repair the connections as necessary.
1) Reconnect all of the disconnected harness connectors.
2) Clear the DTC with a scan tool.
3) Turn OFF the ignition switch for 15 seconds or more.
4) Perform a test drive.
5) Observe the DTC information with a scan tool. Is a DTC set?
Yes
=>Go to SRS control unit replacement.
No
Note
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit removal".
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit installation".
Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit setting".
Procedure completion
1) Reconnect all of the disconnected harness connectors.
2) Clear the DTC with a scan tool.
3) Turn OFF the ignition switch for 15 seconds or more.
4) Turn ON the ignition switch.
5) Observe the DTC information with a scan tool.