DTC P2080:00 [PCM (SKYACTIV-D 2.2)]

id0102j5679000

DTC P2080:00

Exhaust gas temperature sensor No.1 circuit range/performance problem
DETECTION CONDITION
•  With the following conditions met, the difference between the exhaust gas temperature sensor No.1 output value and the exhaust gas temperature sensor No.2 output value is 150 °C {302 °F} or more, or the difference between the exhaust gas temperature sensor No.1 output value and the exhaust gas temperature sensor No.3 output value is 150 °C {302 °F} or more for a continuous 0.128 s.
―  Before starting the engine, leave the vehicle with the engine turned off for 6 h or more.
―  Battery positive voltage: 10 V or more
―  Ignition is switched ON (engine off or on)
―  The following DTCs are not detected
•  ECT sensor: P0118:00, P0117:00
•  Exhaust gas temperature sensor No.2: P2032:00, P2033:00
•  Exhaust gas temperature sensor No.1: P0545:00, P0546:00
•  Malfunction in instrument cluster: P2610:00
•  Exhaust gas temperature sensor No.3: P242C:00, P242D:00
•  Exhaust gas temperature sensor No.2 transistor: P161E:00, P16B2:00
•  Exhaust gas temperature sensor No.3 transistor: P161F:00, P16B3:00
Diagnostic support note
•  This is a continuous monitor (CCM).
•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.
•  FREEZE FRAME DATA/Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
•  Limits engine torque.
•  Limits the maximum engine speed.
•  Inhibits the automatic diesel particulate filter regeneration control.
•  Inhibits the EGR control.
POSSIBLE CAUSE
•  Exhaust gas temperature sensor No.1 connector or terminal malfunction
•  Exhaust gas temperature sensor No.1 malfunction
•  Exhaust gas temperature sensor No.2 connector or terminal malfunction
•  Exhaust gas temperature sensor No.2 malfunction
•  Exhaust gas temperature sensor No.3 connector or terminal malfunction
•  Exhaust gas temperature sensor No.3 malfunction
•  PCM connector or terminal malfunction
•  PCM malfunction
SYSTEM WIRING DIAGRAM
Not applicable


Diagnostic Procedure

Step

Inspection

Results

Action
1
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
Note
•  Recording can be facilitated using the screen capture function of the PC.
•  Record the snap shot data.
—
Go to the next step.
2
INSPECT EXHAUST GAS TEMPERATURE SENSOR NO.1 CONNECTOR CONDITION
•  Switch the ignition OFF.
•  Disconnect the exhaust gas temperature sensor No.1 connector.
•  Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 9.
3
INSPECT EXHAUST GAS TEMPERATURE SENSOR NO.1
•  Inspect exhaust gas temperature sensor No.1.
•  Is exhaust gas temperature sensor No.1 normal?
Yes
Go to the next step.
No
Replace exhaust gas temperature sensor No.1, then go to Step 9.
(See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
4
INSPECT EXHAUST GAS TEMPERATURE SENSOR NO.2 CONNECTOR CONDITION
•  Switch the ignition OFF.
•  Disconnect the exhaust gas temperature sensor No.2 connector.
•  Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 9.
5
INSPECT EXHAUST GAS TEMPERATURE SENSOR NO.2
•  Inspect exhaust gas temperature sensor No.2.
•  Is exhaust gas temperature sensor No.2 normal?
Yes
Go to the next step.
No
Replace exhaust gas temperature sensor No.2, then go to Step 9.
(See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
6
INSPECT EXHAUST GAS TEMPERATURE SENSOR NO.3 CONNECTOR CONDITION
•  Switch the ignition OFF.
•  Disconnect the exhaust gas temperature sensor No.3 connector.
•  Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 9.
7
INSPECT EXHAUST GAS TEMPERATURE SENSOR NO.3
•  Inspect exhaust gas temperature sensor No.3.
•  Is exhaust gas temperature sensor No.3 normal?
Yes
Go to the next step.
No
Replace exhaust gas temperature sensor No.3, then go to Step 9.
(See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
8
INSPECT PCM CONNECTOR CONDITION
•  Disconnect the PCM connector.
•  Inspect the connector engagement and connection condition, and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to the next step.
9
VERIFY THAT REPAIRS HAVE BEEN COMPLETED
•  Reconnect all the disconnected connectors.
•  Refer to the [MEMORY CLEARING PROCEDURE] and clear the DTC.
•  Leave the vehicle for 6 h or more.
•  Switch the ignition ON (engine off) or leave for 1 min while idling.
•  Display the DTCs using the M-MDS.
•  Is DTC P2080:00 displayed?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM, then go to the next step.
No
Go to the next step.
10
VERIFY OTHER DTCs
•  Has any other DTC or pending code been stored?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC TABLE [PCM (SKYACTIV-D 2.2)].)
No
DTC troubleshooting completed.