PERSONALIZATION FEATURES

id120000000000

Caution

• The personalization feature may not be set correctly if [Not Adopted.] or [Not equipped] is selected in the setting displayed on the M-MDS. Do not select [Not Adopted.] or [Not equipped] in the setting displayed on the M-MDS.

Caution

• Settings of some personalization features displayed on the M-MDS cannot be switched depending on the vehicle specification.

• The following systems can be personalized.

• When performing a personalization setting, refer to the referenced section for the detailed setting procedure.

Glass/Windows/Mirrors

Rear window defogger

Personalization features

Setting contents

Setting procedure

Rear window defogger operation time can be changed.

15 minutes / Continuous^*1

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Rear window defogger operation time can be changed.	15 minutes / Continuous^*1	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1:The operation may stop in 15 minutes due to the effect of the outside temperature even if the operation time of the rear window defogger has been changed to Continuous.

Security And Locks

Advanced keyless entry system

Note

• There are three types of personalization procedures: Using the M-MDS, using the center display, and using the remote transmitter button.

Personalization features

Setting contents

Setting procedure

Advanced keyless entry system and push button start system functions can be disabled (disable).

Enable/Disable

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The out-of-area (reception area) type auto lock function can be set.

OFF / ON

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

OFF / ON

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

30 seconds./60 seconds./90 seconds.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The keyless beeper volume can be adjusted.

Off / Low / Medium / High

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / Low / Medium / High

Remote transmitter button is used for the setting.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / Low / Medium / High

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The setting content for the advanced keyless entry system can be returned to the initial value.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Advanced keyless entry system and push button start system functions can be disabled (disable).	Enable/Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The out-of-area (reception area) type auto lock function can be set.	OFF / ON	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
OFF / ON	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds./60 seconds./90 seconds.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The keyless beeper volume can be adjusted.	Off / Low / Medium / High	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / Low / Medium / High	Remote transmitter button is used for the setting. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / Low / Medium / High	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The setting content for the advanced keyless entry system can be returned to the initial value.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Keyless entry system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The advanced keyless entry system and push button start system functions can be disabled (unusable).

Enable/Disable

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

30 seconds./60 seconds./90 seconds.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The setting content for the keyless entry system can be returned to the initial value.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The advanced keyless entry system and push button start system functions can be disabled (unusable).	Enable/Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds./60 seconds./90 seconds.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The setting content for the keyless entry system can be returned to the initial value.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Power door lock system

Note

• There are three types of personalization procedures: Using the M-MDS, using the center display, and using the door lock switch.

Personalization features

Setting contents

Setting procedure

Auto door lock function can be changed.

OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.

Door lock switch is used for the setting.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lock: Shifting from Park Unlock: In Park / Lock: Shifting from Park / Lock: When Driving Unlock: In Park / Lock: When Driving Unlock: IGN Off / Lock: When Driving /Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the door lock system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Auto door lock function can be changed.	OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.	Door lock switch is used for the setting. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Lock: Shifting from Park Unlock: In Park / Lock: Shifting from Park / Lock: When Driving Unlock: In Park / Lock: When Driving Unlock: IGN Off / Lock: When Driving /Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lighting Systems

Turn light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The turn light system can be switched between operable and inoperable.

OFF / ON

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The turn light system can be switched between operable and inoperable.	OFF / ON	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Auto light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

Auto light sensor sensitivity can be changed.

Dark/Medium Dark/Medium/Medium Light/Light

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Med. High / Medium / Med. Low / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Auto light sensor sensitivity can be changed.	Dark/Medium Dark/Medium/Medium Light/Light	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Med. High / Medium / Med. Low / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Coming home light

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The coming home light operation time can be switched.

0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The coming home light operation time can be switched.	0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Leaving home light

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The leaving home light can be switched between operable and inoperable.

Off/On

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The leaving home light can be switched between operable and inoperable.	Off/On	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Room light control system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

• The front/rear map light and courtesy light illumination time after any door is open can be changed.

• The cargo compartment light illumination time after liftgate is open can be changed.

30 minutes./60 minutes./10 minutes.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 minutes / 30 minutes / 10 minutes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The front/rear map light and courtesy light illumination time after all door is closed can be changed.

15 seconds./7.5 seconds./30 seconds./60 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 seconds / 30 seconds / 15 seconds / 7.5 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The down light brightness can be changed when the TNS (parking lights) are turned on.

Bright / Medium / Dark / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
• The front/rear map light and courtesy light illumination time after any door is open can be changed. • The cargo compartment light illumination time after liftgate is open can be changed.	30 minutes./60 minutes./10 minutes.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 minutes / 30 minutes / 10 minutes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The front/rear map light and courtesy light illumination time after all door is closed can be changed.	15 seconds./7.5 seconds./30 seconds./60 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 seconds / 30 seconds / 15 seconds / 7.5 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The down light brightness can be changed when the TNS (parking lights) are turned on.	Bright / Medium / Dark / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Running light system

Personalization features

Setting contents

Setting procedure

The running light system function can be set.

OFF (running light nonillumination)/ON (running light illumination)

Light switch is used for the setting.

(See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The running light system function can be set.	OFF (running light nonillumination)/ON (running light illumination)	Light switch is used for the setting. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Wiper/Washer System

Auto wiper system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The auto wiper function can be disabled.

Off^*1 (Intermittent) / On (Rain Sensing)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The auto wiper function can be disabled.	Off^*1 (Intermittent) / On (Rain Sensing)	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :If the function is set to “Off”, the wipers will operate intermittently with the wiper switch in AUTO position.

Instrumentation/Driver Info.

Turn and hazard indicator alarm

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the turn and hazard indicator alarm can be changed.

Low/High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the turn and hazard indicator alarm can be changed.	Low/High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lights-on reminder warning alarm

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the lights-on reminder warning alarm can be changed.

OFF/Low/High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the lights-on reminder warning alarm can be changed.	OFF/Low/High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :The setting of the lights-on reminder can be changed with the time setting of auto light off system set to Off.

Temperature

Note

• There are two types of personalization procedures; one using the instrument cluster (without center display) and the other using the center display.

Personalization features

Setting contents

Setting procedure

The temperature unit can be changed.^*1

F / C^*2

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

°F /°C^*2

Instrument cluster is used for the setting.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The temperature unit can be changed.^*1	F / C^*2	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
°F /°C^*2	Instrument cluster is used for the setting. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :When the ambient temperature display is switched, the set A/C cabin temperature display is also changed.

*2 :The initial value differs depending on the market.

Active driving display

Personalization features

Setting contents

Setting procedure

Setting can be changed so that the active driving display is not displayed.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The display height (up/down position) can be changed.

13 steps up/down from initial setting (total: 27steps)

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The method for adjusting the display brightness (automatically/manually) can be changed.

AUTO / MANUAL

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The standard brightness with the automatic brightness adjustment can be changed.

2 steps up / down from initial setting (total: 5 steps)

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The standard brightness with the manual brightness adjustment can be changed.

20 steps up / down from initial setting (total: 41 steps)

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The tilt of the displayed image can be adjusted.

3 steps up / down from initial setting (total: 7 steps)

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The street name display can be switched on/off.

Off / Always / On-Demand

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Setting can be changed so that the active driving display is not displayed.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The display height (up/down position) can be changed.	13 steps up/down from initial setting (total: 27steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The method for adjusting the display brightness (automatically/manually) can be changed.	AUTO / MANUAL	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The standard brightness with the automatic brightness adjustment can be changed.	2 steps up / down from initial setting (total: 5 steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The standard brightness with the manual brightness adjustment can be changed.	20 steps up / down from initial setting (total: 41 steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The tilt of the displayed image can be adjusted.	3 steps up / down from initial setting (total: 7 steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The street name display can be switched on/off.	Off / Always / On-Demand	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Parking sensor system

Personalization features

Setting contents

Setting procedure

The parking sensor information can be displayed on the center display.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The parking sensor information can be displayed on the center display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Language

Personalization features

Setting contents

Setting procedure

The display language can be changed.

Depends on market

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The display language can be changed.	Depends on market	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Fuel economy monitor

Personalization features

Setting contents

Setting procedure

The ending screen of the fuel monitor can be switched between display/non-display.

On/Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The function which synchronizes the reset of the fuel reset and trip meters can be switched between on/off.

On/Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The ending screen of the fuel monitor can be switched between display/non-display.	On/Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The function which synchronizes the reset of the fuel reset and trip meters can be switched between on/off.	On/Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

i-ACTIVSENSE

Blind spot monitoring (BSM) system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The system can be changed so that Blind Spot Monitoring (BSM) does not operate.

On / Off

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the blind spot monitoring (BSM) warning alarm can be changed.

OFF/Low/High

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The system can be changed so that Blind Spot Monitoring (BSM) does not operate.	On / Off	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the blind spot monitoring (BSM) warning alarm can be changed.	OFF/Low/High	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lane-keep assist system / Lane departure warning system (LDWS)

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The function of lane departure warning system (LDWS) / lane-keep assist system can be switched.

OFF / LKA / LDWS

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation of the lane-keep assist system warning (steering wheel vibration) can be turned off.

OFF / ON

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

ON / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Intervention is ON

The operation timing of steering wheel operation assist can be changed.

Early / Late

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation sensitivity of steering wheel operation assist can be changed.

High / Med / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation of the lane-keep assist system warning can be turned off.

ON / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Intervention is OFF

The operation timing of lane-keep assist system warning can be changed.

Adaptive / Early / Medium / Late

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The warning operation sensitivity of lane-keep assist system warning can be changed.

High / Med / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The type of the lane-keep assist system warning (type of sound or vibration) can be changed.

Vibration / Rumble Strip / Beep

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The strength of steering wheel vibration can be changed.

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the lane departure warning sound (beep) can be changed.

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the lane departure warning sound (rumble strip) can be changed.

High / Mid / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Mid / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The function of lane departure warning system (LDWS) / lane-keep assist system can be switched.	OFF / LKA / LDWS	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation of the lane-keep assist system warning (steering wheel vibration) can be turned off.	OFF / ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Intervention is ON	The operation timing of steering wheel operation assist can be changed.	Early / Late	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation sensitivity of steering wheel operation assist can be changed.	High / Med / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation of the lane-keep assist system warning can be turned off.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Intervention is OFF	The operation timing of lane-keep assist system warning can be changed.	Adaptive / Early / Medium / Late	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The warning operation sensitivity of lane-keep assist system warning can be changed.	High / Med / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The type of the lane-keep assist system warning (type of sound or vibration) can be changed.	Vibration / Rumble Strip / Beep	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The strength of steering wheel vibration can be changed.	High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the lane departure warning sound (beep) can be changed.	High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the lane departure warning sound (rumble strip) can be changed.	High / Mid / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Mid / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Adaptive front lighting system (AFS)

Personalization features

Setting contents

Setting procedure

The adaptive front lighting system (AFS) can be switched between operable and inoperable.

OFF/ON

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The adaptive front lighting system (AFS) can be switched between operable and inoperable.	OFF/ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

High beam control (HBC) system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The high beam control (HBC) system can be switched between operable and inoperable.

OFF/ON

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The high beam control (HBC) system can be switched between operable and inoperable.	OFF/ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Distance recognition support system (DRSS)

Personalization features

Setting contents

Setting procedure

The operation of distance recognition support system (DRSS) can be turned off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation distance for the alert function can be changed.

Far / Medium / Near

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the distance recognition support system to the initial setting.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of distance recognition support system (DRSS) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation distance for the alert function can be changed.	Far / Medium / Near	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the distance recognition support system to the initial setting.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Advanced smart city brake support (Advanced SCBS)/Smart city brake support [Forward] (SCBS F)/Smart city brake support [Reverse] (SCBS R)/Smart brake support (SBS)

Personalization features

Setting contents

Setting procedure

The operation of Advanced Smart City Brake Support (Advanced SCBS)/Smart City Brake Support [Forward] (SCBS F)/Smart City Brake Support [Reverse] (SCBS R)/Smart Brake Support (SBS) can be turned off.

ON / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The distance at which the collision warning activates can be changed.

Near / Far

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of Advanced Smart City Brake Support (Advanced SCBS)/Smart City Brake Support [Forward] (SCBS F)/Smart City Brake Support [Reverse] (SCBS R)/Smart Brake Support (SBS) warning alarm can be changed.

OFF / Low / High

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of Advanced Smart City Brake Support (Advanced SCBS)/Smart City Brake Support [Forward] (SCBS F)/Smart City Brake Support [Reverse] (SCBS R)/Smart Brake Support (SBS) can be turned off.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance at which the collision warning activates can be changed.	Near / Far	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of Advanced Smart City Brake Support (Advanced SCBS)/Smart City Brake Support [Forward] (SCBS F)/Smart City Brake Support [Reverse] (SCBS R)/Smart Brake Support (SBS) warning alarm can be changed.	OFF / Low / High	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Traffic sign recognition system (TSR)

Personalization features

Setting contents

Setting procedure

The warning pattern of the excessive speed warning can be changed.

Off / Visual / Audio & Visual

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The activation timing for the excessive speed warning can be changed.

+0 / +3 / +5

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The warning pattern of the excessive speed warning can be changed.	Off / Visual / Audio & Visual	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The activation timing for the excessive speed warning can be changed.	+0 / +3 / +5	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

360°view monitor system

Personalization features

Setting contents

Setting procedure

Automatically displays the 360°view monitor system when the ignition is switched ON (engine on).

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The predicted vehicle track display can be switched between display/non-display.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The display of the top view/front view while driving the vehicle in the forward direction after reversing can be switched between display/non-display.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The settings for the 360° view monitor system can be reset to the initial values.

No / Yes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Automatically displays the 360°view monitor system when the ignition is switched ON (engine on).	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The predicted vehicle track display can be switched between display/non-display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The display of the top view/front view while driving the vehicle in the forward direction after reversing can be switched between display/non-display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The settings for the 360° view monitor system can be reset to the initial values.	No / Yes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)