DTC C0061:54 [ADAPTIVE LED HEADLIGHTS CONTROL MODULE (E)]

id1502e4064800

Outline

System malfunction location

Acceleration sensor initial position learning not completed

Detection condition

•  The adaptive LED headlights control module detects that the acceleration sensor initial position learning is not completed.

Fail-safe

•  Control of adaptive LED headlights except for highway mode is continued.

•  The headlight leveling actuator is stopped at the position when the malfunction is determined.

Possible cause

•  Acceleration sensor initial position learning is not completed.

•  Adaptive LED headlights control module internal malfunction

System wiring diagram

Not applicable

Connector diagram

Not applicable

System malfunction location	Acceleration sensor initial position learning not completed
Detection condition	• The adaptive LED headlights control module detects that the acceleration sensor initial position learning is not completed.
Fail-safe	• Control of adaptive LED headlights except for highway mode is continued. • The headlight leveling actuator is stopped at the position when the malfunction is determined.
Possible cause	• Acceleration sensor initial position learning is not completed. • Adaptive LED headlights control module internal malfunction
System wiring diagram	Not applicable
Connector diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Results

Action

1

PERFORM ACCELERATION SENSOR INITIAL POSITION LEARNING

•  Perform the headlight auto leveling system initial setting.
(See HEADLIGHT AUTO LEVELING SYSTEM INITIALIZATION.)

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Perform the DTC inspection for the adaptive LED headlights control module.
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Perform the headlight auto leveling system initial setting again and perform the repair completion verification.

(See HEADLIGHT AUTO LEVELING SYSTEM INITIALIZATION.)

No

Go to repair completion verification 2.

Repair completion verification 1

VERIFY THAT VEHICLE IS REPAIRED

•  Clear the DTC recorded in the memory.
(See CLEARING DTC.)

•  Perform the DTC inspection for the adaptive LED headlights control module.
(See DTC INSPECTION.)

•  Is the same Pending DTC present?

Yes

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [L.H.D. (E)].)

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [R.H.D.].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction recurs, replace the adaptive LED headlights control module, then go to the next step.
(See ADAPTIVE LED HEADLIGHTS CONTROL MODULE REMOVAL/INSTALLATION [(E)].)

No

Go to the next step.

Repair completion verification 2

VERIFY IF OTHER DTC IS DISPLAYED

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

DTC troubleshooting completed.

Step	Inspection	Results	Action
1	PERFORM ACCELERATION SENSOR INITIAL POSITION LEARNING • Perform the headlight auto leveling system initial setting. (See HEADLIGHT AUTO LEVELING SYSTEM INITIALIZATION.) • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the adaptive LED headlights control module. (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Perform the headlight auto leveling system initial setting again and perform the repair completion verification. (See HEADLIGHT AUTO LEVELING SYSTEM INITIALIZATION.)
1		No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED • Clear the DTC recorded in the memory. (See CLEARING DTC.) • Perform the DTC inspection for the adaptive LED headlights control module. (See DTC INSPECTION.) • Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [L.H.D. (E)].) (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [R.H.D.].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction recurs, replace the adaptive LED headlights control module, then go to the next step. (See ADAPTIVE LED HEADLIGHTS CONTROL MODULE REMOVAL/INSTALLATION [(E)].)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTC IS DISPLAYED • Perform the DTC inspection. (See DTC INSPECTION.) • Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.