DTC P0C0D:01 [DRIVE MOTOR CONTROL MODULE (e-SKYACTIV)]

id300203049800

Warning

<<High voltage>>

•  If the necessary measures are not taken before servicing an electric vehicle, it could cause electrical shock and result in serious injury or, in the worst case, death. Before servicing the electric vehicle, refer to [HIGH VOLTAGE SERVICE CAUTIONS] in the general information and implement the necessary measures. (See HIGH VOLTAGE SERVICE CAUTIONS.)

Outline

System malfunction location	Drive motor control module high voltage circuit: Over-voltage malfunction
Detection condition	•  The drive motor control module detects that the voltage value detected by the drive motor control module voltage sensor in the inverter is the specified value or more.
Fail-safe	•  Cuts off the high voltage circuit.
Possible cause	•  Drive motor control module detects high voltage circuit open circuit-related DTC •  Inverter malfunction ―  Drive motor control module input voltage sensor malfunction ―  Drive motor control module malfunction
System wiring diagram	•  Not applicable
Connector diagram	•  Not applicable

Diagnostic Procedure

Warning

<<High voltage>>

•  If necessary measures such as wearing the correct protective gear are not taken when inspecting or removing/installing the high voltage parts, it could cause electrical shock and result in serious injury or, in the worst case, death.

•  Before inspecting or removing/installing the high voltage parts, refer to [HIGH VOLTAGE SERVICE CAUTIONS] in the general information and [High Voltage Part Inspection and Removal/Installation Notes] of the high voltage system service cautions and implement the necessary measures and preparations. (See HIGH VOLTAGE SERVICE CAUTIONS.) (See HIGH VOLTAGE SYSTEM SERVICE CAUTIONS.)

Step	Inspection	Results	Action
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION •  Record the snapshot data. Note •  Recording can be facilitated using the screen capture function of the PC.	—	Go to the next step.
2	VERIFY WHETHER MALFUNCTION IS PRESENT OR PAST •  Clear the DTC recorded in the memory. (See CLEARING DTC.) •  Perform the DTC inspection for the drive motor control module. (See DTC INSPECTION.) •  Is DTC P0C0D:01 a present malfunction?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [L.H.D. (E)].) (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [R.H.D.].) If the CAN communication is normal, replace the drive motor control module and perform the repair completion verification 1. (See INVERTER REMOVAL/INSTALLATION.)
		No	Go to the next step.
3	INSPECT FOR OTHER RELATED DTCs •  Perform the DTC inspection for the drive motor control module. (See DTC INSPECTION.) •  Is the DTC P0D2F:14 displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC P0D2F:14 [DRIVE MOTOR CONTROL MODULE (e-SKYACTIV)].)
		No	The vehicle is normal. •  A temporary malfunction can be considered due to a momentary shut off of the high voltage contactor while driving, such as on a road with unevenness. Go to the next step.
Repair completion verification 1	VERIFY IF OTHER DTCs DISPLAYED •  Perform the DTC inspection. (See DTC INSPECTION.) •  Are any other DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
		No	Go to the next step.
Repair completion verification 2	VERIFY THAT NO OTHER MALFUNCTION OCCURS Warning •  While performing this step, always operate the vehicle in a safe and lawful manner. •  Drive the vehicle for 10 min or more. •  Perform the DTC inspection. (See DTC INSPECTION.) •  Are any DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
		No	DTC troubleshooting completed.