Diagnostic procedure
|
STEP
|
INSPECTION
|
ACTION
|
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related Service Bulletins and/or on-line repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
INSPECT TCM CONNECTOR FOR POOR CONNECTION
• Turn the ignition switch to the LOCK position.
• Disconnect the TCM connector.
• Inspect for poor connection at TCM terminals R18 and R7 (such as damaged/pulled-out pins, corrosion).
• Are terminals normal?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the connector and/or terminal, then go to Step 13.
|
||
|
4
|
INSPECT CONTINUITY OF TURBINE SENSOR CIRCUIT
• Inspect for continuity between the TCM terminals 2A and 2B (wiring harness-side).
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 7.
|
||
|
5
|
INSPECT TURBINE SENSOR SIGNAL CIRCUIT FOR SHORT TO GROUND
• Inspect for continuity between the TCM terminals (wiring harness-side) and body ground.
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the wiring harness for short to ground, then go to Step 10.
|
||
|
6
|
INSPECT TURBINE SENSOR CIRCUIT FOR SHORT TO POWER SUPPLY
• Turn the ignition switch to the ON position (engine off).
• Measure the voltage at TCM (wiring harness-side) terminals 2A and 2B.
• Is there 0 V at the TCM wiring harness-side connector terminals?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the wiring harness for short to power supply, then go to Step 10.
|
||
|
7
|
INSPECT TERMINAL TURBINE SENSOR FOR POOR CONNECTION
• Turn the ignition switch to the LOCK position.
• Disconnect the turbine sensor connector.
• Inspect for poor connection at turbine sensor terminals A and B (such as damaged/pulled-out pins, corrosion).
• Are terminals normal?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the connector and/or terminal, then go to Step 10.
|
||
|
8
|
INSPECT TURBINE SENSOR
• Inspect the turbine sensor.
• Is the turbine sensor normal?
|
Yes
|
Go to the next step.
|
|
No
|
Replace the turbine sensor, then go to Step 10.
|
||
|
9
|
INSPECT TURBINE SENSOR CIRCUIT FOR OPEN CIRCUIT
• Inspect for continuity between turbine sensor terminals (wiring harness-side) and TCM terminals (wiring harness-side).
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Repair or replace the wiring harness for open circuit, then go to the next step.
|
||
|
10
|
VERIFY TROUBLESHOOTING OF DTC P0717 COMPLETED
• Make sure to reconnect all the disconnected connectors.
• Clear the DTC from the memory using the M-MDS.
• Drive the vehicle in D range and make sure that gears shift smoothly from 1GR to 6GR.
• Is same DTC present?
|
Yes
|
Replace the TCM, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
11
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the "After Repair Procedure".
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [SJ6A-EL].)
|
|
No
|
Troubleshooting completed.
|
||
