PERSONALIZATION FEATURES

id120000000000

Caution

• The personalization feature may not be set correctly if [Not equipped] is selected in the setting displayed on the M-MDS. Do not select [Not equipped] in the setting displayed on the M-MDS.

Caution

• Settings of some personalization features cannot be switched depending on the vehicle specification.

• The following systems can be personalized.

• When performing a personalization setting, refer to the referenced section for the detailed setting procedure.

Security And Locks

Advanced keyless entry system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

Advanced keyless entry system and push button start system functions can be disabled (disable).

Enable/Disable

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The out-of-area (reception area) type auto lock function can be set.

OFF / ON

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

OFF / ON

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

30 seconds./60 seconds./90 seconds.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The keyless beeper volume can be adjusted.

Off / Low / Medium / High

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / Low / Medium / High

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The setting content for the advanced keyless entry system can be returned to the initial value.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Advanced keyless entry system and push button start system functions can be disabled (disable).	Enable/Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The out-of-area (reception area) type auto lock function can be set.	OFF / ON	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
OFF / ON	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds./60 seconds./90 seconds.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The keyless beeper volume can be adjusted.	Off / Low / Medium / High	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / Low / Medium / High	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The setting content for the advanced keyless entry system can be returned to the initial value.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Keyless entry system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The keyless entry system and push button start system functions can be disabled (unusable).

Enable/Disable

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

30 seconds./60 seconds./90 seconds.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The setting content for the keyless entry system can be returned to the initial value.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The keyless entry system and push button start system functions can be disabled (unusable).	Enable/Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds./60 seconds./90 seconds.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The setting content for the keyless entry system can be returned to the initial value.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Power door lock system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

Auto door lock function can be changed.

Off/

Lock: When Driving, Unlock: In Park./

Lock When Driving./

Lock: Driving, Unlock: IGN Off./

Lock When Shifting Out Of P./

Lock: Shift From P, Unlock: In P.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off /

Lock: When Driving, Unlock: In Park /

Lock: When Driving / Lock: When Driving, Unlock: IGN Off /

Lock: Shifting from Park

/ Lock: Shifting from Park, Unlock: In Park

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the door lock system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Auto door lock function can be changed.	Off/ Lock: When Driving, Unlock: In Park./ Lock When Driving./ Lock: Driving, Unlock: IGN Off./ Lock When Shifting Out Of P./ Lock: Shift From P, Unlock: In P.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / Lock: When Driving, Unlock: In Park / Lock: When Driving / Lock: When Driving, Unlock: IGN Off / Lock: Shifting from Park / Lock: Shifting from Park, Unlock: In Park	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lighting Systems

Auto light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

Auto light sensitivity can be changed.

Extra Low (Except Japan)/Low (All Others)/Standard (All Others)/High (Except Japan)/Extra High (Except Japan)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Light / Medium Light / Medium / Medium Dark / Dark

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Auto light sensitivity can be changed.	Extra Low (Except Japan)/Low (All Others)/Standard (All Others)/High (Except Japan)/Extra High (Except Japan)	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Light / Medium Light / Medium / Medium Dark / Dark	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Turn light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The operation of the three-flash turn signal function can be disabled.

Off/On

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of the three-flash turn signal function can be disabled.	Off/On	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Coming home light system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The coming home light system operation time can be switched.

0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The coming home light system operation time can be switched.	0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Leaving home light system

Note

• There are three methods for personalizing the leaving home light system: Using the M-MDS, using the center display, and using the light switch.

Personalization features

Setting contents

Setting procedure

The leaving home light system can be switched between operable and inoperable.

Off/On

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Operable/Inoperable

Light switch is used for the setting.

(See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The leaving home light system can be switched between operable and inoperable.	Off/On	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Operable/Inoperable	Light switch is used for the setting. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Interior light control system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

• The map light illumination time after a door is opened can be changed.

• The trunk compartment light illumination time after the trunk lid is opened can be changed.

30 minutes./60 minutes./10 minutes.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 minutes / 30 minutes / 10 minutes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The map light illumination time after all doors are closed can be changed.

15 seconds./7.5 seconds./30 seconds./60 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 seconds / 30 seconds / 15 seconds / 7.5 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
• The map light illumination time after a door is opened can be changed. • The trunk compartment light illumination time after the trunk lid is opened can be changed.	30 minutes./60 minutes./10 minutes.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 minutes / 30 minutes / 10 minutes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The map light illumination time after all doors are closed can be changed.	15 seconds./7.5 seconds./30 seconds./60 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 seconds / 30 seconds / 15 seconds / 7.5 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Running light system

Personalization features

Setting contents

Setting procedure

The running light system function can be set.

Off (Running light non-illumination)/On (Running light illumination)

Light switch is used for the setting.

(See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The running light system function can be set.	Off (Running light non-illumination)/On (Running light illumination)	Light switch is used for the setting. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Wiper/Washer System

Auto wiper system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The auto wiper function can be disabled.

Off^*1 (Intermittent) / On (Rain Sensing)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The auto wiper function can be disabled.	Off^*1 (Intermittent) / On (Rain Sensing)	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :If the function is set to “Off”, the wipers will operate intermittently with the wiper switch in AUTO position.

Entertainment

Language

Personalization features

Setting contents

Setting procedure

The display language can be changed.

Depends on market^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The display language can be changed.	Depends on market^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :Available only in display from the center display.

Fuel economy monitor

Personalization features

Setting contents

Setting procedure

The ending screen of the fuel monitor can be switched between display/non-display.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The function which synchronizes the reset of the fuel reset and trip meters can be switched between on/off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The ending screen of the fuel monitor can be switched between display/non-display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The function which synchronizes the reset of the fuel reset and trip meters can be switched between on/off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Instrumentation/Driver Info.

Turn and hazard indicator alarm

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the turn and hazard indicator alarm can be changed.

Low/High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the turn and hazard indicator alarm can be changed.	Low/High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lights-on reminder warning alarm

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the lights-on reminder warning alarm can be changed.

OFF/Low/High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the lights-on reminder warning alarm can be changed.	OFF/Low/High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :The setting of the lights-on reminder can be changed with the time setting of auto light off system set to Off.

Temperature

Note

• There are two types of personalization procedures; one using the instrument cluster (without center display) and the other using the center display.

Personalization features

Setting contents

Setting procedure

The temperature unit can be changed.^*1

°F /°C^*2

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

°F /°C^*2

Instrument cluster is used for the setting.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The temperature unit can be changed.^*1	°F /°C^*2	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
°F /°C^*2	Instrument cluster is used for the setting. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :When the ambient temperature display is switched, the set A/C cabin temperature display is also changed.

*2 :The initial value differs depending on the market.

Distance

Personalization features

Setting contents

Setting procedure

The distance unit can be changed.

Miles / Km^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The distance unit can be changed.	Miles / Km^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :The initial value differs depending on the market.

i-ACTIVSENSE

Lane Departure Warning System (LDWS)

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the LDWS warning alarm (Beep) can be changed.

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the LDWS warning alarm (Rumble) can be changed.

High / Mid / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the LDWS warning alarm can be changed.

Volume 1 / Volume 2 / Volume 3

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

The type of the LDWS warning alarm can be changed.

Beep / Rumble

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

Beep / Rumble

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The distance between the warning-trigger lines for the Lane Departure Warning System (LDWS) and vehicle lanes can be changed.

Adaptive / Early / Medium / Late

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

Adaptive / Early / Medium / Late

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The warning operation sensitivity of the lane departure warning system (LDWS) can be changed.

Often/Medium/Rare

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

Often/Medium/Rare

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lane departure warning system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the LDWS warning alarm (Beep) can be changed.	High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the LDWS warning alarm (Rumble) can be changed.	High / Mid / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the LDWS warning alarm can be changed.	Volume 1 / Volume 2 / Volume 3	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
The type of the LDWS warning alarm can be changed.	Beep / Rumble	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
Beep / Rumble	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance between the warning-trigger lines for the Lane Departure Warning System (LDWS) and vehicle lanes can be changed.	Adaptive / Early / Medium / Late	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
Adaptive / Early / Medium / Late	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The warning operation sensitivity of the lane departure warning system (LDWS) can be changed.	Often/Medium/Rare	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
Often/Medium/Rare	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lane departure warning system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

High Beam Control (HBC) system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The high beam control (HBC) system can be switched between operable and inoperable.

OFF/ON

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The high beam control (HBC) system can be switched between operable and inoperable.	OFF/ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Adaptive front lighting system (AFS)

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The adaptive front lighting system (AFS) can be switched between operable and inoperable.

OFF/ON

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the adaptive front lighting system (AFS) to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The adaptive front lighting system (AFS) can be switched between operable and inoperable.	OFF/ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the adaptive front lighting system (AFS) to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Adaptive LED headlight system

Personalization features

Setting contents

Setting procedure

The adaptive LED headlights can be switched between operable and inoperable.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the adaptive LED headlights to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The adaptive LED headlights can be switched between operable and inoperable.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the adaptive LED headlights to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Blind Spot Monitoring (BSM) system

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the blind spot monitoring (BSM) warning buzzer can be changed.

OFF/Low/High

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the blind spot monitoring (BSM) warning buzzer can be changed.	OFF/Low/High	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
	High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)