PERSONALIZATION FEATURES

id120000000000

Caution

• The personalization feature may not be set correctly if [Not equipped] is selected in the setting displayed on the M-MDS. Do not select [Not equipped] in the setting displayed on the M-MDS.

Caution

• Settings of some personalization features displayed on the M-MDS cannot be switched depending on the vehicle specification.

• The following systems can be personalized.

• When performing a personalization setting, refer to the referenced section for the detailed setting procedure.

Glass/Windows/Mirrors

Rear window defogger

Personalization features

Setting contents

Setting procedure

Rear window defogger operation time can be changed.

15 minutes/Continuous

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Rear window defogger operation time can be changed.	15 minutes/Continuous	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Security And Locks

Advanced keyless entry system

Personalization features

Setting contents

Setting procedure

Advanced keyless entry system and push button start system functions can be disabled (disable).

Enable/Disable

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The out-of-area (reception area) type auto lock function can be set.

OFF / ON

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

OFF / ON

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

30 seconds./60 seconds./90 seconds.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The keyless beeper volume can be adjusted.

Off / Low / Medium / High

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / Low / Medium / High

Remote transmitter button is used for the setting.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / Low / Medium / High

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The setting content for the advanced keyless entry system can be returned to the initial value.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Advanced keyless entry system and push button start system functions can be disabled (disable).	Enable/Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The out-of-area (reception area) type auto lock function can be set.	OFF / ON	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
OFF / ON	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds./60 seconds./90 seconds.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The keyless beeper volume can be adjusted.	Off / Low / Medium / High	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / Low / Medium / High	Remote transmitter button is used for the setting. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / Low / Medium / High	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The setting content for the advanced keyless entry system can be returned to the initial value.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Keyless entry system

Personalization features

Setting contents

Setting procedure

The keyless entry system and push button start system functions can be disabled.

Enable/Disable

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation start time of the auto re-lock function can be changed.

30 seconds./60 seconds./90 seconds.

M-MDS is used.

(See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)

30 seconds / 60 seconds / 90 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The setting content for the keyless entry system can be returned to the initial value.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The keyless entry system and push button start system functions can be disabled.	Enable/Disable	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation start time of the auto re-lock function can be changed.	30 seconds./60 seconds./90 seconds.	M-MDS is used. (See SECURITY AND LOCKS PERSONALIZATION FEATURES SETTING PROCEDURE.)
30 seconds / 60 seconds / 90 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The setting content for the keyless entry system can be returned to the initial value.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Power door lock system

Personalization features

Setting contents

Setting procedure

Auto door lock function can be changed.

OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.

Door lock switch is used for the setting.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lock: Shifting from Park Unlock: In Park / Lock: Shifting from Park / Lock: When Driving Unlock: In Park / Lock: When Driving Unlock: IGN Off / Lock: When Driving /Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the door lock system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Auto door lock function can be changed.	OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
OFF / Lock When Driving. / Lock: Driving, Unlock: IGN Off. / Lock When Shifting Out Of P. / Lock: Shift From P, Unlock: In P.	Door lock switch is used for the setting. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Lock: Shifting from Park Unlock: In Park / Lock: Shifting from Park / Lock: When Driving Unlock: In Park / Lock: When Driving Unlock: IGN Off / Lock: When Driving /Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the door lock system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lighting Systems

Turn light system

Personalization features

Setting contents

Setting procedure

The operation of the three-flash turn signal function can be disabled.

Off (except for Israel)/On (for Israel)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of the three-flash turn signal function can be disabled.	Off (except for Israel)/On (for Israel)	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Auto light system

Personalization features

Setting contents

Setting procedure

Auto light sensitivity can be changed.

Extra Low (Except Japan)/Low (All Others)/Standard (All Others)/High (Except Japan)/Extra High (Except Japan)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Light / Medium Light / Medium / Medium Dark / Dark

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Auto light sensitivity can be changed.	Extra Low (Except Japan)/Low (All Others)/Standard (All Others)/High (Except Japan)/Extra High (Except Japan)	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Light / Medium Light / Medium / Medium Dark / Dark	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Coming home light

Personalization features

Setting contents

Setting procedure

The coming home light operation time can be switched.

0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The coming home light operation time can be switched.	0 seconds./30 seconds./60 seconds./90 seconds./120 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Off / 30 seconds / 60 seconds / 90 seconds / 120 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Leaving home light

Personalization features

Setting contents

Setting procedure

The leaving home light can be switched between operable and inoperable.

Off/On

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Operable/Inoperable

Light switch is used for the setting.

(See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The leaving home light can be switched between operable and inoperable.	Off/On	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Operable/Inoperable	Light switch is used for the setting. (See LIGHTING SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Room light control system

Personalization features

Setting contents

Setting procedure

• The map light illumination time after a door is opened can be changed.

• The trunk compartment light (4SD)/cargo compartment light (5HB) illumination time after the trunk lid (4SD)/liftgate (5HB) is opened can be changed.

30 minutes./60 minutes./10 minutes.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 minutes / 30 minutes / 10 minutes

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The map light illumination time after all doors are closed can be changed.

15 seconds./7.5 seconds./30 seconds./60 seconds.

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

60 seconds / 30 seconds / 15 seconds / 7.5 seconds

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
• The map light illumination time after a door is opened can be changed. • The trunk compartment light (4SD)/cargo compartment light (5HB) illumination time after the trunk lid (4SD)/liftgate (5HB) is opened can be changed.	30 minutes./60 minutes./10 minutes.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 minutes / 30 minutes / 10 minutes	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The map light illumination time after all doors are closed can be changed.	15 seconds./7.5 seconds./30 seconds./60 seconds.	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
60 seconds / 30 seconds / 15 seconds / 7.5 seconds	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Wiper/Washer System

Auto wiper system

Personalization features

Setting contents

Setting procedure

The auto wiper function can be disabled.

Off^*1 (Intermittent) / On (Rain Sensing)

M-MDS is used.

(See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The auto wiper function can be disabled.	Off^*1 (Intermittent) / On (Rain Sensing)	M-MDS is used. (See CONTROL SYSTEM PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :If the function is set to “Off”, the wipers will operate intermittently with the wiper switch in AUTO position.

Entertainment

Language

Personalization features

Setting contents

Setting procedure

The turn-by-turn display can be switched between display/non-display.

English/French/German/Italian/Spanish/Russian/Portuguese/Dutch/Swedish/Danish/Norwegian/Finnish/Czech/Slovakian/Hungarian/Turkish/Polish/Estonian/Latvian/Lithuanian/Greek/Croatian/Bulgarian/Romanian/Serbian/Hebrew

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The turn-by-turn display can be switched between display/non-display.	English/French/German/Italian/Spanish/Russian/Portuguese/Dutch/Swedish/Danish/Norwegian/Finnish/Czech/Slovakian/Hungarian/Turkish/Polish/Estonian/Latvian/Lithuanian/Greek/Croatian/Bulgarian/Romanian/Serbian/Hebrew	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Active driving display

Personalization features

Setting contents

Setting procedure

Setting can be changed so that the active driving display is not displayed.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The display height (up/down position) can be changed.

13 steps up/down from initialsetting (total: 27steps)

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The method for adjusting the display brightness (automatically/manually) can be changed.

AUTO / MANUAL

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The standard brightness with the automatic brightness adjustment can be changed.

2 steps up / down from initial setting (total: 5steps)

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The standard brightness with the manual brightness adjustment can be changed.

20 steps up / down from initial setting (total: 41steps)

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The turn-by-turn display can be switched between display/non-display.

At Manoeuvre / Lane Guidance & Turn by Turn / Street Name & Turn by Turn / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
Setting can be changed so that the active driving display is not displayed.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The display height (up/down position) can be changed.	13 steps up/down from initialsetting (total: 27steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The method for adjusting the display brightness (automatically/manually) can be changed.	AUTO / MANUAL	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The standard brightness with the automatic brightness adjustment can be changed.	2 steps up / down from initial setting (total: 5steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The standard brightness with the manual brightness adjustment can be changed.	20 steps up / down from initial setting (total: 41steps)	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The turn-by-turn display can be switched between display/non-display.	At Manoeuvre / Lane Guidance & Turn by Turn / Street Name & Turn by Turn / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Fuel economy monitor

Personalization features

Setting contents

Setting procedure

The ending screen of the fuel monitor can be switched between display/non-display.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The function which synchronizes the reset of the fuel reset and trip meters can be switched between on/off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The ending screen of the fuel monitor can be switched between display/non-display.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The function which synchronizes the reset of the fuel reset and trip meters can be switched between on/off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Instrumentation/Driver Info.

Turn and hazard indicator alarm

Personalization features

Setting contents

Setting procedure

The volume of the turn and hazard indicator alarm can be changed.

Low/High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the turn and hazard indicator alarm can be changed.	Low/High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lights-on reminder warning alarm

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the lights-on reminder warning alarm can be changed.

OFF/Low/High

M-MDS is used.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the lights-on reminder warning alarm can be changed.	OFF/Low/High	M-MDS is used. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :The setting of the lights-on reminder can be changed with the time setting of auto light off system set to Off.

Temperature

Note

• There are two types of personalization procedures; one using the instrument cluster (without center display) and the other using the center display.

Personalization features

Setting contents

Setting procedure

The temperature unit can be changed.^*1

°F /°C^*2

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

°F /°C^*2

Instrument cluster is used for the setting.

(See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The temperature unit can be changed.^*1	°F /°C^*2	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
°F /°C^*2	Instrument cluster is used for the setting. (See INSTRUMENT CLUSTER PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :When the ambient temperature display is switched, the set A/C cabin temperature display is also changed.

*2 :The initial value differs depending on the market.

Distance

Personalization features

Setting contents

Setting procedure

The distance unit can be changed.

Miles / Km^*1

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The distance unit can be changed.	Miles / Km^*1	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

*1 :The initial value differs depending on the market.

i-Activsense

Blind spot monitoring (BSM) system

Personalization features

Setting contents

Setting procedure

The volume of the blind spot monitoring (BSM) warning alarm can be changed.

OFF/Low/High

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation of blind spot monitoring (BSM) system can be turned off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the blind spot monitoring (BSM) warning alarm can be changed.	OFF/Low/High	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation of blind spot monitoring (BSM) system can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Lane departure warning system (LDWS)

Note

• There are two types of personalization procedures; one using the M-MDS and the other using the center display.

Personalization features

Setting contents

Setting procedure

The volume of the LDWS warning alarm (Rumble) can be changed.

High / Mid / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The volume of the LDWS warning alarm (Beep) can be changed.

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The type of the LDWS warning alarm can be changed.(with center display)

Beep / Rumble

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

Beep / Rumble

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The distance between the warning-trigger lines for the Lane Departure Warning System (LDWS) and vehicle lanes can be changed.

Adaptive / Early / Medium / Late

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

Before / At Line

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The warning operation sensitivity of the lane departure warning system (LDWS) can be changed.

Often/Medium/Rare

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

High / Low

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lane departure warning system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the LDWS warning alarm (Rumble) can be changed.	High / Mid / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The volume of the LDWS warning alarm (Beep) can be changed.	High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The type of the LDWS warning alarm can be changed.(with center display)	Beep / Rumble	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
Beep / Rumble	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance between the warning-trigger lines for the Lane Departure Warning System (LDWS) and vehicle lanes can be changed.	Adaptive / Early / Medium / Late	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
Before / At Line	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The warning operation sensitivity of the lane departure warning system (LDWS) can be changed.	Often/Medium/Rare	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
High / Low	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lane departure warning system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

High beam control (HBC) system

Personalization features

Setting contents

Setting procedure

The high beam control (HBC) system can be switched between operable and inoperable.

OFF/ON

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Returns the setting content of the lighting system to the initial setting.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The high beam control (HBC) system can be switched between operable and inoperable.	OFF/ON	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
Returns the setting content of the lighting system to the initial setting.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Adaptive LED headlight system

Personalization features

Setting contents

Setting procedure

The adaptive LED headlights function can be turned off.

YES / NO

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The adaptive LED headlights function can be turned off.	YES / NO	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Distance recognition support system (DRSS)

Personalization features

Setting contents

Setting procedure

The operation of distance recognition support system (DRSS) can be turned off.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation distance for the alert function can be changed.

Far / Medium / Near

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The operation of distance recognition support system (DRSS) can be turned off.	On / Off	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation distance for the alert function can be changed.	Far / Medium / Near	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart City Brake Support [Forward/Reverse] (SCBS F/R)

Personalization features

Setting contents

Setting procedure

The Smart City Brake Support [Forward/Reverse] (SCBS F/R) can be switched between operable and inoperable.

ON / OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The Smart City Brake Support [Forward/Reverse] (SCBS F/R) can be switched between operable and inoperable.	ON / OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Smart brake support (SBS)

Personalization features

Setting contents

Setting procedure

The volume of the smart brake support (SBS) warning alarm can be changed.

OFF / Low / High

M-MDS is used.

(See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)

High/Low/OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The operation of Smart Brake Support (SBS) can be turned off.

ON/OFF

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

The distance at which the collision warning activates can be changed.

Near/Far

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Personalization features	Setting contents	Setting procedure
The volume of the smart brake support (SBS) warning alarm can be changed.	OFF / Low / High	M-MDS is used. (See i-ACTIVSENSE PERSONALIZATION FEATURES SETTING PROCEDURE.)
High/Low/OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The operation of Smart Brake Support (SBS) can be turned off.	ON/OFF	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)
The distance at which the collision warning activates can be changed.	Near/Far	Center display is used for the setting. (See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)

Driver Attention Alert System

Personalization features

Setting contents

Setting procedure

The system can be changed so that driver attention alert does not operate.

On / Off

Center display is used for the setting.

(See CENTER DISPLAY PERSONALIZATION FEATURES SETTING PROCEDURE.)