DTC P0500:00 [ZJ, ZY]

id0102c0704800

DTC P0500:00

VSS circuit problem

DETECTION CONDITION

•  If the wheel speed input via CAN from the ABS HU/CM or DSC HU/CM is abnormal.

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.

•  PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA is available.

•  The DTC is stored in the PCM memory.

POSSIBLE CAUSE

•  PCM configuration error

•  ABS HU/CM or DSC HU/CM DTC is stored

•  ABS wheel-speed sensor connector or terminals malfunction

•  ABS wheel-speed sensor malfunction

•  PCM connector or terminals malfunction

•  PCM malfunction

DTC P0500:00	VSS circuit problem
DETECTION CONDITION	• If the wheel speed input via CAN from the ABS HU/CM or DSC HU/CM is abnormal. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM. • PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA is available. • The DTC is stored in the PCM memory.
POSSIBLE CAUSE	• PCM configuration error • ABS HU/CM or DSC HU/CM DTC is stored • ABS wheel-speed sensor connector or terminals malfunction • ABS wheel-speed sensor malfunction • PCM connector or terminals malfunction • PCM malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Perform the “PCM CONFIGURATION”, then go to the next step. (See PCM CONFIGURATION [ZJ, ZY].)
3	VERIFY DTC TROUBLESHOOTING COMPLETED • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [ZJ, ZY].) • Repeat twice the following steps. 1. Start the engine and drive the vehicle. 2. Turn the ignition switch off. • Start the engine and drive the vehicle again. • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [ZJ, ZY].) • Is the PENDING CODE for this DTC present?	Yes	Go to the next step.
3		No	Go to Step 10.
4	VERIFY STORED DTC IN ABS HU/CM OR DSC HU/CM • Turn the ignition switch to the ON position (engine off). • Verify stored DTCs in ABS HU/CM or DSC HU/CM using the M-MDS. (See ON-BOARD DIAGNOSIS [ABS].) (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].) • Are any DTCs present?	Yes	Go to the appropriate DTC inspection. (See ON-BOARD DIAGNOSIS [ABS].) (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
4		No	Go to the next step.
5	VERIFY CURRENT INPUT SIGNAL STATUS • Connect the M-MDS to the DLC-2. • Start the engine. • Perform the PID/DATA Monitor and Record Procedure and access the VSS PID. (See ON-BOARD DIAGNOSTIC TEST [ZJ, ZY].) ― Vehicle speed 20 km/h {12.4 mph}: 20km/h {12.4 mph} ― Vehicle speed 40 km/h {24.8 mph}: 40km/h {24.8 mph} • Are the PID readings within the specification?	Yes	Go to the symptom troubleshooting “INTERMITTENT CONCERN TROUBLESHOOTING”. (See INTERMITTENT CONCERN TROUBLESHOOTING [ZJ, ZY].)
5		No	Go to the next step.
6	INSPECT ABS WHEEL‐SPEED SENSOR CONNECTOR AND TERMINALS • Turn the ignition switch off. • Disconnect the ABS wheel-speed sensor connector. • Inspect for poor connection (such as damaged, pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector or terminals, then go to Step 9.
6		No	Go to the next step.
7	INSPECT ABS WHEEL‐SPEED SENSOR • Inspect the ABS wheel‐speed sensor. (See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.) (See REAR ABS WHEEL-SPEED SENSOR INSPECTION.) • Is there any malfunction?	Yes	Replace the ABS wheel‐speed sensor, then go to Step 9. (See FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION.) (See REAR ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION.)
7		No	Go to the next step.
8	INSPECT PCM CONNECTOR AND TERMINALS • Disconnect the PCM connector. • Inspect for poor connection (such as damaged, pulled-out pins, and corrosion). • Is there any malfunction?	Yes	Repair or replace the connector or terminals, then go to the next step.
8		No	Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [ZJ, ZY].) • Repeat twice the following steps. 1. Start the engine and drive the vehicle. 2. Turn the ignition switch off. • Start the engine and drive the vehicle again. • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [ZJ, ZY].) • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [ZJ, ZY].)
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [ZJ, ZY].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [ZJ, ZY].)
10		No	DTC troubleshooting completed.