DTC P0087:00 [MZ-CD 1.6]

DTC P0087:00	Fuel pressure - too low
DETECTION CONDITION	• The PCM monitors the fuel pressure using the fuel pressure sensor. If the fuel pressure sensor output voltage is less than 0.424 V after starting or stopping the engine, the PCM determines that the fuel pressure is too low.
POSSIBLE CAUSE	• Leakage or clogging in fuel line • Restriction or damage in fuel filter • Fuel pressure sensor malfunction (built-in common rail) • Fuel injection pump learned values reset improper • Fuel metering valve malfunction (built-in supply pump) • Supply pump malfunction • PCM malfunction

DTC P0087:00

Fuel pressure - too low

DETECTION CONDITION

• The PCM monitors the fuel pressure using the fuel pressure sensor. If the fuel pressure sensor output voltage is less than 0.424 V after starting or stopping the engine, the PCM determines that the fuel pressure is too low.

POSSIBLE CAUSE

• Leakage or clogging in fuel line

• Restriction or damage in fuel filter

• Fuel pressure sensor malfunction (built-in common rail)

• Fuel injection pump learned values reset improper

• Fuel metering valve malfunction (built-in supply pump)

• Supply pump malfunction

• PCM malfunction

STEP	INSPECTION	ACTION
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
No	Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY • Verify related service repair information availability. • Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. • If the vehicle is not repaired, go to the next step.
No	Go to the next step.
3	VERIFY RELATED PENDING CODE AND/OR DTC • Switch the ignition to off, then to ON (engine off). • Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [MZ-CD 1.6].) • Is the following PENDING CODE/DTC also present? ― P0192:00, P0193:00, P0251:00, P0253:00, P0254:00	Yes	Go to the applicable DTC inspection. (See DTC P0192:00 [MZ-CD 1.6].) (See DTC P0193:00 [MZ-CD 1.6].) (See DTC P0251:00 [MZ-CD 1.6].) (See DTC P0253:00 [MZ-CD 1.6].) (See DTC P0254:00 [MZ-CD 1.6].)
No	Go to the next step.
4	INSPECT FUEL LINE • Switch the ignition to off. • Inspect for fuel leakage or clogging in the following fuel lines: ― Fuel tank and fuel filter ― Fuel filter and supply pump • Is there any malfunction?	Yes	Repair or replace suspect fuel line, then go to Step 7.
No	Go to the next step.
5	INSPECT FUEL PRESSURE SENSOR • Inspect the fuel pressure sensor. • Is there any malfunction?	Yes	Replace the common rail, then go to Step 7. (See COMMON RAIL REMOVAL/INSTALLATION [MZ-CD 1.6].)
No	Go to the next step.
6	PERFORM FUEL INJECTION PUMP LEARNED VALUES RESET • Clear the DTC from the PCM memory using the M-MDS. • Perform the FUEL INJECTION PUMP LEARNED VALUES RESET. (See FUEL INJECTION PUMP LEARNED VALUES RESET [MZ-CD 1.6].) • Run the vehicle under the FREEZE FRAME DATA stored condition • Is the same DTC present?	Yes	Replace the supply pump. (Fuel pressure regulator or fuel metering valve malfunction) Then go to the next step.
No	Go to Step 8.
7	VERIFY THAT DTC P0087:00 TROUBLESHOOTING IS COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. • Run the vehicle under the FREEZE FRAME DATA stored condition. • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [MZ-CD 1.6].) Go to the next step.
No	Go to the next step.
8	VERIFY AFTER REPAIR PROCEDURE • Perform the after repair procedure. (See AFTER REPAIR PROCEDURE [MZ-CD 1.6].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [MZ-CD 1.6].)
No	DTC troubleshooting completed.

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA HAS BEEN RECORDED

• Has the FREEZE FRAME DATA been recorded?

Yes

Go to the next step.

Record the FREEZE FRAME DATA on the repair order, then go to the next step.

VERIFY RELATED REPAIR INFORMATION AVAILABILITY

• Verify related service repair information availability.

• Is any related repair information available?

Yes

Perform repair or diagnosis according to the available repair information.

• If the vehicle is not repaired, go to the next step.

Go to the next step.

VERIFY RELATED PENDING CODE AND/OR DTC

• Switch the ignition to off, then to ON (engine off).

• Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.

(See ON-BOARD DIAGNOSTIC TEST [MZ-CD 1.6].)

• Is the following PENDING CODE/DTC also present?

― P0192:00, P0193:00, P0251:00, P0253:00, P0254:00

Yes

Go to the applicable DTC inspection.

(See DTC P0192:00 [MZ-CD 1.6].)

(See DTC P0193:00 [MZ-CD 1.6].)

(See DTC P0251:00 [MZ-CD 1.6].)

(See DTC P0253:00 [MZ-CD 1.6].)

(See DTC P0254:00 [MZ-CD 1.6].)

Go to the next step.

INSPECT FUEL LINE

• Switch the ignition to off.

• Inspect for fuel leakage or clogging in the following fuel lines:

― Fuel tank and fuel filter

― Fuel filter and supply pump

• Is there any malfunction?

Yes

Repair or replace suspect fuel line, then go to Step 7.

Go to the next step.

INSPECT FUEL PRESSURE SENSOR

• Inspect the fuel pressure sensor.

• Is there any malfunction?

Yes

Replace the common rail, then go to Step 7.

(See COMMON RAIL REMOVAL/INSTALLATION [MZ-CD 1.6].)

Go to the next step.

PERFORM FUEL INJECTION PUMP LEARNED VALUES RESET

• Clear the DTC from the PCM memory using the M-MDS.

• Perform the FUEL INJECTION PUMP LEARNED VALUES RESET.

(See FUEL INJECTION PUMP LEARNED VALUES RESET [MZ-CD 1.6].)

• Run the vehicle under the FREEZE FRAME DATA stored condition

• Is the same DTC present?

Yes

Replace the supply pump.

(Fuel pressure regulator or fuel metering valve malfunction)

Then go to the next step.

Go to Step 8.

VERIFY THAT DTC P0087:00 TROUBLESHOOTING IS COMPLETED

• Make sure to reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS.

• Run the vehicle under the FREEZE FRAME DATA stored condition.

• Is the same DTC present?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the PCM.

(See PCM REMOVAL/INSTALLATION [MZ-CD 1.6].)

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

• Perform the after repair procedure.

(See AFTER REPAIR PROCEDURE [MZ-CD 1.6].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [MZ-CD 1.6].)

DTC troubleshooting completed.