DTC P0500:00 [MZR-CD 2.2]

id0102f3704800

DTC P0500:00

VSS circuit malfunction
DETECTION CONDITION
•  The PCM monitors the vehicle speed signal from the ABS, ABS/TCS HU/CM. If the vehicle speed signal is not correct, the PCM determines that the vehicle speed signal from ABS, ABS/TCS HU/CM has malfunction.
Monitoring condition
•  Battery voltage: more than 10 V
Diagnostic support note
•  The MIL illuminates if the PCM detects the above malfunction condition in first drive cycle.
•  PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.
•  FREEZE FRAME DATA (mode2) and snapshot data are available.
•  The DTC is stored in the PCM memory.
POSSIBLE CAUSE
•  PCM configuration error
•  DSC HU/CM DTC is stored
•  ABS wheel-speed sensor connector or terminals malfunction
•  ABS wheel-speed sensor malfunction
•  PCM connector or terminals malfunction
•  PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION
1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED (MODE2)
•  Is DTC P0500:00 on FREEZE FRAME DATA (mode2)?
Yes
Go to the next step.
No
Go to troubleshooting procedures for DTC in FREEZE FRAME DATA (mode2).
(See DTC TABLE [MZR-CD 2.2].)
2
VERIFY RELATED SERVICE INFORMATION
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to available Service Information.
•  If vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY STORED DTC IN OR DSC HU/CM
•  Turn the ignition switch to the ON position (engine off).
•  Verify stored DTCs in ABS HU/CM or DSC HU/CM using the M-MDS.
•  Are any DTCs present?
Yes
Go to the appropriate DTC inspection.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
No
Go to the next step.
4
VERIFY CURRENT INPUT SIGNAL STATUS
•  Connect the M-MDS to the DLC-2.
•  Start the engine.
•  Perform the PID/DATA Monitor and Record Procedure and access the VSS PID.
―  Vehicle speed 20 km/h {12.4 mph}: 20km/h {12.4 mph}
―  Vehicle speed 40 km/h {24.8 mph}: 40km/h {24.8 mph}
•  Are the PID readings within the specification?
Yes
Go to the symptom troubleshooting “INTERMITTENT CONCERN TROUBLESHOOTING”.
(See INTERMITTENT CONCERN TROUBLESHOOTING [MZR-CD 2.2].)
No
Go to the next step.
5
INSPECT ABS WHEEL‐SPEED SENSOR CONNECTOR AND TERMINALS
•  Turn the ignition switch off.
•  Disconnect the ABS wheel-speed sensor connector.
•  Inspect for poor connection (such as damaged, pulled-out pins, and corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector or terminals, then go to Step 9.
No
Go to the next step.
6
INSPECT ABS WHEEL‐SPEED SENSOR
•  Inspect the ABS wheel‐speed sensor.
•  Is there any malfunction?
Yes
Replace the ABS wheel‐speed sensor, then go to Step 9.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
(See REAR ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION.)
No
Go to the next step.
7
INSPECT PCM CONNECTOR AND TERMINALS
•  Disconnect the PCM connector.
•  Inspect for poor connection (such as damaged, pulled-out pins, and corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector or terminals, then go to the next step.
No
Go to the next step.
8
VERIFY TROUBLESHOOTING OF DTC P0500:00 COMPLETED
•  Make sure to reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Drive the vehicle under the FREEZE FRAME DATA (mode2) condition.
•  Is the PENDING CODE same as the DTC present?
Yes
Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [MZR-CD 2.2].)
No
Go to the next step.
9
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [MZR-CD 2.2].)
No
DTC troubleshooting completed.