DTC C006A:04/C006A:47 [DYNAMIC STABILITY CONTROL (DSC)]


id0402b2879300

Note
•  Only vehicles with combined sensor.
Applied VIN (assumed):
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 100001—181415
•  JMZ BL12F70# 100001—181415
•  JMZ BL12Y20# 100001—181415
•  JMZ BL12Z20# 100001—181415
•  JMZ BL12Z50# 100001—181415
•  JMZ BL14F60# 100001—181415
•  JMZ BL14F70# 100001—181415
•  JMZ BL14Y20# 100001—181415
•  JMZ BL14Z20# 100001—181415
•  JMZ BL14Z50# 100001—181415
•  JMZ BLA2A60# 100001—181415
•  JMZ BLA2C60# 100001—181415
•  JMZ BLA2F70# 100001—181415
•  JMZ BLA2G60# 100001—181415
•  JMZ BLA2Y60# 100001—181415
•  JMZ BLA2Z20# 100001—181415
•  JMZ BLA2Z50# 100001—181415
•  JMZ BLA4360# 100001—181415
•  JMZ BLA4A60# 100001—181415
•  JMZ BLA4C60# 100001—181415
•  JMZ BLA4F70# 100001—181415
•  JMZ BLA4G60# 100001—181415
•  JMZ BLA4Y60# 100001—181415
•  JMZ BLA4Z20# 100001—181415
•  JMZ BLA4Z50# 100001—181415
Australian specs.
•  JM0 BL103100 100001—225632
•  JM0 BL10C100 100001—225632
•  JM0 BL10F100 100001—225632
•  JM0 BL10L100 100001—225632
General (R.H.D.) specs.
•  JM6 BL1031*0 100001—225632
•  JM6 BL1051*0 100001—225632
•  JM6 BL10F1*0 100001—225632
•  JM6 BL10L1*0 100001—225632
•  JM6 BL10Z1*0 100001—225632
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 100001—225632
•  JM7 BL04Z**# 100001—225632
•  JM7 BL12F**# 100001—225632
•  JM7 BL12Z**# 100001—225632
•  JM7 BL14F**# 100001—225632
•  JM7 BL14Z**# 100001—225632
•  JM7 BL22F**# 100001—225632
•  JM7 BL22Z**# 100001—225632
•  JM7 BL24F**# 100001—225632
•  JM7 BL24Z**# 100001—225632

DTC
C006A:04, C006A:47
Combined sensor (internal malfunction)
DETECTION CONDITION
•  Combined sensor internal malfunction is detected.
POSSIBLE CAUSE
•  Combined sensor internal malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION

1
VERIFY COMBINED SENSOR MALFUNCTION
•  Clear the DTCs from the memory.
•  Start the engine and drive the vehicle at 10 km/h {6.2 mph} or more.
•  Are the same DTCs present?
Yes
Replace the combined sensor, then go to the next step.
No
Go to the next step.
2
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Clear the DTCs from the memory.
•  Start the engine and drive the vehicle at 10 km/h {6.2 mph} or more.
•  Are the same DTCs present?
Yes
Repeat the inspection from Step 1.
If the malfunction recurs, replace the DSC HU/CM, then go to the next step.
No
Go to the next step.
3
VERIFY THAT NO OTHER DTCS ARE PRESENT
•  Are any other DTCs output?
Yes
Go to the applicable DTC inspection.
No
DTC troubleshooting completed.