DTC C006A:95 [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2884900

Note
•  Only vehicles with combined sensor.
Applied VIN (assumed):
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 100001—181415
•  JMZ BL12F70# 100001—181415
•  JMZ BL12Y20# 100001—181415
•  JMZ BL12Z20# 100001—181415
•  JMZ BL12Z50# 100001—181415
•  JMZ BL14F60# 100001—181415
•  JMZ BL14F70# 100001—181415
•  JMZ BL14Y20# 100001—181415
•  JMZ BL14Z20# 100001—181415
•  JMZ BL14Z50# 100001—181415
•  JMZ BLA2A60# 100001—181415
•  JMZ BLA2C60# 100001—181415
•  JMZ BLA2F70# 100001—181415
•  JMZ BLA2G60# 100001—181415
•  JMZ BLA2Y60# 100001—181415
•  JMZ BLA2Z20# 100001—181415
•  JMZ BLA2Z50# 100001—181415
•  JMZ BLA4360# 100001—181415
•  JMZ BLA4A60# 100001—181415
•  JMZ BLA4C60# 100001—181415
•  JMZ BLA4F70# 100001—181415
•  JMZ BLA4G60# 100001—181415
•  JMZ BLA4Y60# 100001—181415
•  JMZ BLA4Z20# 100001—181415
•  JMZ BLA4Z50# 100001—181415
Australian specs.
•  JM0 BL103100 100001—225632
•  JM0 BL10C100 100001—225632
•  JM0 BL10F100 100001—225632
•  JM0 BL10L100 100001—225632
General (R.H.D.) specs.
•  JM6 BL1031*0 100001—225632
•  JM6 BL1051*0 100001—225632
•  JM6 BL10F1*0 100001—225632
•  JM6 BL10L1*0 100001—225632
•  JM6 BL10Z1*0 100001—225632
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 100001—225632
•  JM7 BL04Z**# 100001—225632
•  JM7 BL12F**# 100001—225632
•  JM7 BL12Z**# 100001—225632
•  JM7 BL14F**# 100001—225632
•  JM7 BL14Z**# 100001—225632
•  JM7 BL22F**# 100001—225632
•  JM7 BL22Z**# 100001—225632
•  JM7 BL24F**# 100001—225632
•  JM7 BL24Z**# 100001—225632

DTC
C006A:95
Combined sensor mismatched installation
DETECTION CONDITION
•  Communication error with combined sensor is detected in CAN communication (CAN2 line).
POSSIBLE CAUSE
•  Mismatched installation of combined sensor

Diagnostic procedure

STEP

INSPECTION

ACTION
1
INSPECT COMBINED SENSOR FOR MISMATCHED INSTALLATION
•  Verify combined sensor part number.
•  Has a combined sensor with the correct part number been installed?
Yes
Go to the next step.
No
Replace with correct combined sensor part number, then go to the next step.
(See COMBINED SENSOR REMOVAL/INSTALLATION.)
2
VERIFY THAT THE SAME DTC IS NOT PRESENT
•  Clear the DTCs from the memory.
•  Are the same DTCs present?
Yes
Repeat the inspection from Step 1.
If the malfunction recurs, replace the DSC HU/CM, then go to the next step.
(See DSC HU/CM REMOVAL/INSTALLATION.)
No
Go to the next step.
3
VERIFY THAT NO OTHER DTCS ARE PRESENT
•  Are any other DTCs output?
Yes
Go to the applicable DTC inspection.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
No
DTC troubleshooting completed.