DTC U0452:86 [DYNAMIC STABILITY CONTROL (DSC)]

DTC U0452:86 [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2893000

Note

• Only vehicles without combined sensor.

Applied VIN (assumed):

European (L.H.D. U.K.) specs.

• JMZ BL12F60# 181416—

• JMZ BL12F70# 181416—

• JMZ BL12Y20# 181416—

• JMZ BL12Z20# 181416—

• JMZ BL12Z50# 181416—

• JMZ BL14F60# 181416—

• JMZ BL14F70# 181416—

• JMZ BL14Y20# 181416—

• JMZ BL14Z20# 181416—

• JMZ BL14Z50# 181416—

• JMZ BLA2A60# 181416—

• JMZ BLA2C60# 181416—

• JMZ BLA2F70# 181416—

• JMZ BLA2G60# 181416—

• JMZ BLA2Y60# 181416—

• JMZ BLA2Z20# 181416—

• JMZ BLA2Z50# 181416—

• JMZ BLA4360# 181416—

• JMZ BLA4A60# 181416—

• JMZ BLA4C60# 181416—

• JMZ BLA4F70# 181416—

• JMZ BLA4G60# 181416—

• JMZ BLA4Y60# 181416—

• JMZ BLA4Z20# 181416—

• JMZ BLA4Z50# 181416—

Australian specs.

• JM0 BL103100 225633—

• JM0 BL10C100 225633—

• JM0 BL10F100 225633—

• JM0 BL10L100 225633—

General (R.H.D.) specs.

• JM6 BL1031*0 225633—

• JM6 BL1051*0 225633—

• JM6 BL10F1*0 225633—

• JM6 BL10L1*0 225633—

• JM6 BL10Z1*0 225633—

General (L.H.D.) specs., Arab Gulf Cooperation Council, China

• JM7 BL04F**# 225633—

• JM7 BL04Z**# 225633—

• JM7 BL12F**# 225633—

• JM7 BL12Z**# 225633—

• JM7 BL14F**# 225633—

• JM7 BL14Z**# 225633—

• JM7 BL22F**# 225633—

• JM7 BL22Z**# 225633—

• JM7 BL24F**# 225633—

• JM7 BL24Z**# 225633—

DTC

U0452:86

Abnormal message from SAS control module

DETECTION CONDITION

• Correct data cannot be received from SAS control module

POSSIBLE CAUSE

• SAS control module malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	INSPECT FOR SAS CONTROL MODULE MALFUNCTION • Switch the ignition to off. • Using the M-MDS, perform the DTC inspection for the SAS control module. (See DTC INSPECTION [TYPE B].) • Are any DTCs detected?	Yes	Go to applicable DTC inspection. (See DTC TABLE [TYPE B].)
1		No	Go to the next step.
2	VERIFY THAT THE SAME DTC IS NOT PRESENT • Clear the DTCs from the memory. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].) • Are the same DTCs present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the SAS control module, then go to the next step. (See SAS CONTROL MODULE REMOVAL/INSTALLATION.)
2		No	Go to the next step.
3	VERIFY THAT NO OTHER DTCS ARE PRESENT • Are any other DTCs output?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
3		No	DTC troubleshooting completed.