DTC P2119[L3 Turbo]

DTC P2119	Throttle actuator control throttle body range/performance problem
DETECTION CONDITION	• The PCM compares the TP with the default TP when the ignition switch is off. If the TP is higher than the default TP, the PCM determines that there is a throttle actuator control throttle body range/performance problem. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunctioning condition in the first drive cycles. • FREEZE FRAME DATA is available. • DTCs are stored in the PCM memory.
POSSIBLE CAUSE	• Throttle actuator malfunction • Throttle valve malfunction • PCM malfunction

DTC P2119

Throttle actuator control throttle body range/performance problem

DETECTION CONDITION

• The PCM compares the TP with the default TP when the ignition switch is off. If the TP is higher than the default TP, the PCM determines that there is a throttle actuator control throttle body range/performance problem.

Diagnostic support note

• This is a continuous monitor (CCM).

• The MIL illuminates if the PCM detects the above malfunctioning condition in the first drive cycles.

• FREEZE FRAME DATA is available.

• DTCs are stored in the PCM memory.

POSSIBLE CAUSE

• Throttle actuator malfunction

• Throttle valve malfunction

• PCM malfunction

STEP	INSPECTION	ACTION
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
No	Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform the repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
No	Go to the next step.
3	INSPECT THROTTLE ACTUATOR • Inspect the throttle actuator. (See THROTTLE ACTUATOR INSPECTION[L3 Turbo].) • Is there any malfunction?	Yes	Replace the throttle body, then go to Step 5. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 Turbo].)
No	Go to the next step.
4	INSPECT TP SENSOR • Inspect the TP sensor. (See THROTTLE ACTUATOR INSPECTION[L3 Turbo].) • Is there any malfunction?	Yes	Replace the TP sensor, then go to the next step. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 Turbo].)
No	Go to the next step.
5	VERIFY TROUBLESHOOTING OF DTC P2119 COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. • Turn the ignition switch to the ON position (Engine off), then off. • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION[L3 Turbo].)
No	Go to the next step.
6	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE[L3 Turbo].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE[L3 Turbo].)
No	DTC troubleshooting completed.

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA HAS BEEN RECORDED

• Has the FREEZE FRAME DATA been recorded?

Yes

Go to the next step.

Record the FREEZE FRAME DATA on the repair order, then go to the next step.

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

• Verify related Service Information availability.

• Is any related Service Information available?

Yes

Perform the repair or diagnosis according to the available Service Information.

• If the vehicle is not repaired, go to the next step.

Go to the next step.

INSPECT THROTTLE ACTUATOR

• Inspect the throttle actuator.

(See THROTTLE ACTUATOR INSPECTION[L3 Turbo].)

• Is there any malfunction?

Yes

Replace the throttle body, then go to Step 5.

(See INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 Turbo].)

Go to the next step.

INSPECT TP SENSOR

• Inspect the TP sensor.

(See THROTTLE ACTUATOR INSPECTION[L3 Turbo].)

• Is there any malfunction?

Yes

Replace the TP sensor, then go to the next step.

(See INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 Turbo].)

Go to the next step.

VERIFY TROUBLESHOOTING OF DTC P2119 COMPLETED

• Make sure to reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS.

• Turn the ignition switch to the ON position (Engine off), then off.

• Is the PENDING CODE for this DTC present?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION[L3 Turbo].)

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

• Perform the “AFTER REPAIR PROCEDURE”.

(See AFTER REPAIR PROCEDURE[L3 Turbo].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE[L3 Turbo].)

DTC troubleshooting completed.