REAR WIPER MOTOR INSPECTION

id091900801500


Rear Wiper Motor Inspection


VIN: Except 3MZ

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the following parts:

(1)  Rear wiper arm and blade (See REAR WIPER ARM AND BLADE REMOVAL/INSTALLATION.)
(2)  Liftgate upper trim (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
(3)  Liftgate side trim (See LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.)
(4)  Liftgate recess (See LIFTGATE RECESS REMOVAL/INSTALLATION.)
(5)  Liftgate lower trim (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION.)

3.  Disconnect the connector. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)

4.  Apply battery positive voltage to rear wiper motor terminal B and connect terminal A to the ground, and then verify the operation condition.

am3zzw00020282

•  If the rear wiper motor does not operate normally, replace it. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)


VIN: 3MZ

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the following parts:

(1)  Rear wiper arm and blade (See REAR WIPER ARM AND BLADE REMOVAL/INSTALLATION.)
(2)  Liftgate upper trim (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
(3)  Liftgate side trim (See LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.)
(4)  Liftgate recess (See LIFTGATE RECESS REMOVAL/INSTALLATION.)
(5)  Liftgate lower trim (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION.)

3.  Disconnect the connector. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)

4.  Apply battery positive voltage to rear wiper motor terminal C and connect terminal D to the ground, and then verify the operation condition.

am3zzw00020145

•  If the rear wiper motor does not operate normally, replace it. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)


Auto-stop Operation Inspection


VIN: Except 3MZ

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the following parts:

(1)  Rear wiper arm and blade (See REAR WIPER ARM AND BLADE REMOVAL/INSTALLATION.)
(2)  Liftgate upper trim (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
(3)  Liftgate side trim (See LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.)
(4)  Liftgate recess (See LIFTGATE RECESS REMOVAL/INSTALLATION.)
(5)  Liftgate lower trim (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION.)

3.  Disconnect the connector. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)

4.  Apply battery positive voltage to rear wiper motor terminal B and connect terminals A and C to the ground, and then operate the rear wiper motor.

am3zzw00020282

5.  Disconnect the battery voltage from terminal B during rear wiper motor operation, and stop the rear wiper motor mid-way.

6.  Verify that the rear wiper stops at the park position as a result of the auto-stop operating.

•  If the rear wiper does not stop at the park position, replace the rear wiper motor. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)


VIN: 3MZ

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the following parts:

(1)  Rear wiper arm and blade (See REAR WIPER ARM AND BLADE REMOVAL/INSTALLATION.)
(2)  Liftgate upper trim (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
(3)  Liftgate side trim (See LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.)
(4)  Liftgate recess (See LIFTGATE RECESS REMOVAL/INSTALLATION.)
(5)  Liftgate lower trim (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION.)

3.  Disconnect the connector. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)

4.  Apply battery positive voltage to rear wiper motor terminal C and connect terminals D and B to the ground, and then operate the rear wiper motor.

am3zzw00020145

5.  Disconnect the battery voltage from terminal C during rear wiper motor operation, and stop the rear wiper motor mid-way.

6.  Verify that the rear wiper stops at the park position as a result of the auto-stop operating.

•  If the rear wiper does not stop at the park position, replace the rear wiper motor. (See REAR WIPER MOTOR REMOVAL/INSTALLATION.)