DTC P0236:00 [MZ-CD 1.6]
id0102g8023600
|
DTC P0236:00 |
Manifold absolute pressure (MAP) sensor signal gradient not compatible |
|---|---|
|
DETECTION CONDITION
|
• The PCM monitors the MAP sensor signal voltage. If the change in manifold pressure which the MAP sensor detects exceeds 19.9997 kPa {0.204 kgf/cm2, 2.901 psi}/10 ms, the PCM determines that the MAP sensor signal gradient is incompatible.
|
|
POSSIBLE CAUSE
|
• Improper operation of
• Leakage or air suction at intake-air system
• MAP sensor connector or terminal malfunction
• MAP sensor malfunction
• MAP sensor loose installation
• Blockage of MAP sensor detection area, or foreign matter adhering
• PCM malfunction
|
Diagnostic procedure
|
STEP |
INSPECTION |
ACTION |
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
VERIFY RELATED PENDING CODE AND/OR DTC
• Switch the ignition to off, then to ON (engine off).
• Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
• Is the following PENDING CODE/DTC also present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
Go to the next step.
|
||
|
4
|
VERIFY INTAKE-AIR SYSTEM COMPONENTS CONDITION
• Verify the intake-air system components for following:
• Is there any malfunction?
|
Yes
|
Repair or replace malfunctioning part, then go to Step 11.
|
|
No
|
Go to the next step.
|
||
|
5
|
VERIFY VBC SOLENOID VALVE HOSE CONDITION
• Verify the VBC solenoid valve hose for following:
• Is there any malfunction?
|
Yes
|
Repair or replace malfunctioning part, then go to Step 11.
|
|
No
|
Go to the next step.
|
||
|
6
|
INSPECT VBC SOLENOID VALVE
• Inspect the VBC solenoid valve.
• Is there any malfunction?
|
Yes
|
Replace the VBC solenoid valve, then go to Step 11.
|
|
No
|
Go to the next step.
|
||
|
7
|
INSPECT MAP SENSOR CONNECTOR CONDITION
• Switch the ignition to off.
• Disconnect the MAP sensor connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion)
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to Step 11.
|
|
No
|
Go to the next step.
|
||
|
8
|
VERIFY MAP SENSOR INSTALLATION
• Verify MAP sensor installation.
• Is the MAP sensor installed properly?
|
Yes
|
Install the MAP sensor properly, then go to Step 11.
|
|
No
|
Go to the next step.
|
||
|
9
|
INSPECT MAP SENSOR
• Reconnect the MAP sensor connector.
• Inspect the MAP sensor.
• Is there any malfunction?
|
Yes
|
Go to the next step.
|
|
No
|
Intermittent concern exists.
Go to the Step 11.
|
||
|
10
|
VERIFY IF CAUSE IS FOREIGN MATTER ADHERING TO MAP SENSOR DETECTION AREA
• Verify that foreign matter is not adhering to the MAP sensor detection area.
• Is foreign matter adhering?
|
Yes
|
Remove the foreign matter, then go to the next step.
|
|
No
|
Replace the MAP sensor, then go to the next step.
|
||
|
11
|
VERIFY THAT DTC P0236:00 TROUBLESHOOTING IS COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Run the vehicle under the FREEZE FRAME DATA stored condition.
• Is the same DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
|
No
|
Go to the next step.
|
||
|
12
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the after repair procedure.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
DTC troubleshooting completed.
|
||