DTC P02E9:00 [MZ-CD 1.6]
id0102g8348700
DTC P02E9:00 |
Intake shutter valve position sensor circuit high input |
---|---|
DETECTION CONDITION
|
• The PCM monitors the input signal from the intake shutter valve position sensor. If the voltage from the intake shutter valve position sensor is more than 4.951 V, the PCM determines that there is a malfunction in the intake shutter valve position sensor circuit.
|
POSSIBLE CAUSE
|
• Intake shutter valve position sensor connector or terminal malfunction
• PCM connector or terminal malfunction
• Short to power supply in wiring harness between intake shutter valve position sensor terminal B and PCM terminal 2AU
• Intake shutter valve position sensor power circuit and signal circuit are shorted each other
• Intake shutter valve position sensor malfunction
• Open circuit in wiring harness between intake shutter valve position sensor terminal C and PCM terminal 2AG
• PCM malfunction
|
![]() |
Diagnostic procedure
STEP |
INSPECTION |
ACTION |
|
---|---|---|---|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
2
|
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
• Verify related Service Information availability.
• Is any related Service Information available?
|
Yes
|
Perform the repair or diagnosis according to the available Service Information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
3
|
INSPECT INTAKE SHUTTER VALVE POSITION SENSOR CONNECTOR FOR POOR CONNECTION
• Switch the ignition to off.
• Disconnect the intake shutter valve position sensor connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to Step 9.
|
No
|
Go to the next step.
|
||
4
|
INSPECT PCM CONNECTOR FOR POOR CONNECTION
• Disconnect the PCM connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to Step 9.
|
No
|
Go to the next step.
|
||
5
|
INSPECT INTAKE SHUTTER VALVE POSITION SENSOR SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY
• Switch the ignition to ON (engine off).
• Measure the voltage at the intake shutter valve position sensor terminal B (wiring harness-side)
• Is the voltage more than 4.951 V?
|
Yes
|
Repair or replace the wiring harness for a possible short to power supply, then go to Step 9.
|
No
|
Go to the next step.
|
||
6
|
INSPECT INTAKE SHUTTER VALVE POSITION SENSOR POWER SUPPLY CIRCUIT AND SIGNAL CIRCUIT FOR SHORT TO EACH OTHER
• Switch the ignition to off.
• Intake shutter valve position sensor and PCM connectors are disconnected.
• Inspect for continuity between intake shutter valve position terminals B and C (wiring harness-side).
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness for a possible short to each other, then go to Step 9.
|
No
|
Go to the next step.
|
||
7
|
INSPECT INTAKE SHUTTER VALVE POSITION SENSOR
• Inspect the intake shutter valve position sensor.
• Is there any malfunction?
|
Yes
|
Replace the intake shutter valve, then go to Step 9.
|
No
|
Go to the next step.
|
||
8
|
INSPECT INTAKE SHUTTER VALVE POSITION SENSOR GROUND CIRCUIT FOR OPEN CIRCUIT
• Inspect for continuity between intake shutter valve position sensor terminal C and PCM terminal 2AG.
• Is there continuity?
|
Yes
|
Go to the next step.
|
No
|
Repair or replace the wiring harness for an open circuit, then go to the next step.
|
||
9
|
VERIFY THAT DTC P02E9:00 TROUBLESHOOTING IS COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Start the engine.
• Is the same DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
No
|
Go to the next step.
|
||
10
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the after repair procedure.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6])
|
No
|
DTC troubleshooting completed.
|