DTC P042F:00 [MZ-CD 1.6]
id0102g8714400
|
DTC P042F:00 |
EGR valve stuck closed |
|---|---|
|
DETECTION CONDITION
|
• The PCM monitors the EGR valve position using the EGR valve position sensor. The PCM compares the target and actual EGR positions. If the PCM detects that actual EGR valve position falls below the target position excessively while the EGR valve is moving to open, the PCM determines that the EGR valve is stuck closed.
|
|
POSSIBLE CAUSE
|
• Connector or terminal malfunction
• Obstruction in EGR valve
• EGR valve malfunction
• PCM malfunction
|
Diagnostic procedure
|
STEP |
INSPECTION |
ACTION |
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
VERIFY RELATED PENDING CODE AND/OR DTC
• Switch the ignition to ON (engine off).
• Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
• Is the other PENDING CODE/DTC also present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
Go to the next step.
|
||
|
4
|
IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA
• Is P0404:00 on FREEZE FRAME DATA?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
Go to the next step.
|
||
|
5
|
INSPECT EGR VALVE CONNECTOR FOR POOR CONNECTION
• Switch the ignition to off.
• Disconnect the EGR valve connector.
• Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace terminal, then go to Step 8.
|
|
No
|
Go to the next step.
|
||
|
6
|
VISUALLY INSPECT EGR VALVE
• Disconnect the EGR valve connector.
• Remove the EGR valve without the EGR cooler hose disconnected.
• Visually inspect the EGR valve.
• Is there any obstruction (carbon deposit etc.) in EGR valve?
|
Yes
|
Remove the obstruction, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
7
|
INSPECT THE EGR VALVE
• Inspect the EGR valve.
• Is the EGR valve normal?
|
Yes
|
Go to the next step.
|
|
No
|
Replace the EGR valve.
Then go to the next step.
|
||
|
8
|
VERIFY THAT DTC P042F:00 TROUBLESHOOTING IS COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Run the vehicle under the FREEZE FRAME DATA stored condition.
• Is the same DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
|
No
|
Go to the next step.
|
||
|
9
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the after repair procedure.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
DTC troubleshooting completed.
|
||