ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FN4A-EL]
id050218290300
1. Connect the M-MDS (IDS) to the DLC-2.
am3uuw00002614
|
2. After the vehicle is identified, select the following items from the initialization screen of the IDS.
3. Select the applicable PID from the PID table.
4. Verify the PID data according to the detections on the screen.
PID/DATA Monitor Table (Reference)
Monitor item |
Unit/Condition |
Test condition |
Specification |
Inspection item |
---|---|---|---|---|
DWN SW
|
On/Off
|
Selector lever at shift down position
|
On
|
• Down switch
• Related harness
|
Except selector lever at shift down position
|
Off
|
|||
ECT
|
°C {°F}
|
ECT 20°C {68°F}
|
Approx.20°C {68°F}
|
• PCM
|
GEAR
|
1st/2nd/3rd/4th
|
1GR
|
1st
|
• Following PIDs:
|
2GR
|
2nd
|
|||
3GR
|
3rd
|
|||
4GR
|
4th
|
|||
HTM_CNT
|
—
|
This PID indicates number of high oil temperature mode operations.
High oil temperature mode is switched when ATF reaches approx.130 °C {266 °F} or more.
|
||
HTM_DIS
|
km {mile}
|
This PID indicates travel distance after operation of high oil temperature mode.
High oil temperature mode is switched when ATF reaches approx.130 °C {266 °F} or more.
|
||
LINEDES
|
Pa {kgf/cm2, psi}
|
Idle at P position after warm-up
|
Approx.400 kPa {4.08 kgf/cm2, 58.0 psi}
|
• Following PIDs:
|
Engine speed 2,000 rpm at P position
|
Approx.560 kPa {5.71 kgf/cm2, 81.2psi}
|
|||
LPS
|
A
|
Idle at P position after warm-up
|
Approx.950 mA
|
• Pressure control solenoid
• Related harness
|
Engine speed 2,000 rpm at P position
|
Approx.830 mA
|
|||
MNL SW
|
On/Off
|
Selector lever at P position
|
Off
|
• M range switch
• Related harness
|
Selector lever at R position
|
Off
|
|||
Selector lever at N position
|
Off
|
|||
Selector lever at D range
|
Off
|
|||
Selector lever at M range
|
On
|
|||
OSS
|
RPM
|
Vehicle stopped
|
0 RPM
|
• VSS
• Related harness
|
Vehicle speed 30 km/h {19 mph} in 3GR
|
Approx.250 RPM
|
|||
RPM
|
RPM
|
Engine speed 1,000 rpm
|
Approx.1,000 RPM
|
• PCM
|
SSA/SS1
|
%
|
1GR at D range
|
0 %
|
• Shift solenoid A
• Related harness
|
2GR at D range
|
0 %
|
|||
3GR at D range
|
0 %
|
|||
4GR at D range
|
Approx.100 %
|
|||
SSB/SS2
|
%
|
1GR at D range
|
Approx.100 %
|
• Shift solenoid B
• Related harness
|
2GR at D range
|
0 %
|
|||
3GR at D range
|
0 %
|
|||
4GR at D range
|
0 %
|
|||
SSC/SS3
|
%
|
1GR at D range
|
Approx.100 %
|
• Shift solenoid C
• Related harness
|
2GR at D range
|
Approx.100 %
|
|||
3GR at D range
|
0 %
|
|||
4GR at D range
|
0 %
|
|||
SSD/SS4
|
On/Off
|
1GR at D range
|
Off
|
• Shift solenoid D
• Related harness
|
2GR at D range
|
Off
|
|||
3GR at D range
|
Off
|
|||
4GR at D range
|
On
|
|||
SSE_SS5
|
On/Off
|
TCC released
|
Off
|
• Shift solenoid E
• Related harness
|
TCC engaged
|
On
|
|||
TFT
|
°C {°F}
|
ATF 20 °C {68°F}
|
Approx.20 °C {68°F}
|
• TFT sensor
• Related harness
|
ATF 65 °C {149°F}
|
Approx.65 °C {149°F}
|
|||
TFTV
|
V
|
ATF 20 °C {68°F}
|
Approx.3.3 V
|
• TFT sensor
• Related harness
|
ATF 65 °C {149°F}
|
Approx.1.3 V
|
|||
TR
|
P/R/N/D
|
Selector lever at P position
|
P
|
• TR switch
• Related harness
|
Selector lever at R position
|
R
|
|||
Selector lever at N position
|
N
|
|||
Selector lever at D range
|
D
|
|||
Selector lever at M range
|
D
|
|||
TR_SENS
|
V
|
Selector lever at P position
|
4.3—4.8
|
• TR switch
• Related harness
|
Selector lever at R position
|
3.8—4.2
|
|||
Selector lever at N position
|
3.0—3.5
|
|||
Selector lever at D range
|
2.2—2.7
|
|||
Selector lever at M range
|
2.2—2.7
|
|||
TSS
|
RPM
|
Engine speed 1,000 rpm at P position
|
Approx.950 RPM
|
• Input/turbine speed sensor
• Related harness
|
Vehicle stopped at D range
|
0 RPM
|
|||
UP SW
|
On/Off
|
Selector lever at shift up position
|
On
|
• Up switch
• Related harness
|
Except selector lever at shift up position
|
Off
|
|||
VPWR
|
V
|
Under any condition
|
B+
|
• Battery
• Related harness
|
VSS
|
KPH {MPH}
|
Vehicle stopped
|
Approx.0 KPH {0 MPH}
|
• VSS
• Related harness
|
Vehicle speed 30 km/h {19 MPH}
|
Approx.30 KPH {19 MPH}
|