SECURITY LIGHT: NOT ILLUMINATED, DTC B10E6:12/- [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)]

id09021d905600

DTC

Security light flashing pattern

—

Coil antenna power supply circuit malfunction

M-MDS display

Keyless control module

B10E6:12

PCM

—

DETECTION CONDITION

•  Voltage higher than the specification (2.2—6.5 V) is detected for 0.05 s while the coil antenna power supply circuit is not active.

POSSIBLE CAUSE

•  Coil antenna connector or terminals malfunction

•  Push button start connector or terminals malfunction

•  Keyless control module connector or terminals malfunction

•  Short to power supply in wiring harness between the following terminals:

―  Push button start terminal C—Keyless control module terminal 4Q

―  Coil antenna terminal A—Keyless control module terminal 4Q

―  Coil antenna terminal B—Keyless control module terminal 4Q

•  Push button start malfunction

•  Coil antenna malfunction

•  Keyless control module malfunction

DTC	Security light flashing pattern	—	Coil antenna power supply circuit malfunction
DETECTION CONDITION	• Voltage higher than the specification (2.2—6.5 V) is detected for 0.05 s while the coil antenna power supply circuit is not active.
POSSIBLE CAUSE	• Coil antenna connector or terminals malfunction • Push button start connector or terminals malfunction • Keyless control module connector or terminals malfunction • Short to power supply in wiring harness between the following terminals: ― Push button start terminal C—Keyless control module terminal 4Q ― Coil antenna terminal A—Keyless control module terminal 4Q ― Coil antenna terminal B—Keyless control module terminal 4Q • Push button start malfunction • Coil antenna malfunction • Keyless control module malfunction

System Wiring Diagram

am6zzw00006141

Diagnostic Procedure

STEP

INSPECTION

ACTION

1

INSPECT COIL ANTENNA CONNECTOR AND TERMINALS

•  Switch the ignition to off.

•  Disconnect the negative battery cable.

•  Disconnect the coil antenna connector.

•  Inspect the connector and terminals (corrosion, damage, pin disconnection).

•  Is there any malfunction?

Yes

Repair or replace the connector or terminals, then go to Step 7.

No

Go to the next step.

2

INSPECT PUSH BUTTON START CONNECTOR AND TERMINALS

•  Disconnect the push button start connector.

•  Inspect the connector and terminals (corrosion, damage, pin disconnection).

•  Is there any malfunction?

Yes

Repair or replace the connector or terminals, then go to Step 7.

No

Go to the next step.

3

INSPECT KEYLESS CONTROL MODULE CONNECTOR AND TERMINALS

•  Disconnect the keyless control module connector.

•  Inspect the connector and terminals (corrosion, damage, pin disconnection).

•  Is there any malfunction?

Yes

Repair or replace the connector or terminals, then go to Step 7.

No

Go to the next step.

4

INSPECT COIL ANTENNA POWER SUPPLY CIRCUIT FOR SHORT TO POWER SUPPLY

•  Coil antenna, push button start and keyless control module connectors are disconnected.

•  Reconnect the negative battery cable.

•  Measure the voltage at the keyless control module terminal 4Q (wiring harness-side).

•  Is the voltage 2.2 V or more?

Yes

Repair or replace the wiring harness for a possible short to power supply, then go to Step 7.

No

Go to the next step.

5

INSPECT PUSH BUTTON START

•  Inspect the push button start.
(See PUSH BUTTON START INSPECTION [WITH ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].)

•  Is there any malfunction?

Yes

Replace the push button start, then go to Step 7.

(See PUSH BUTTON START REMOVAL/INSTALLATION [WITH ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].)

No

Go to the next step.

6

VERIFY COIL ANTENNA MALFUNCTION

•  Make sure to reconnect all disconnected connectors.

•  Reconnect the negative battery cable.

•  Clear the DTC from the keyless control module using the M-MDS.
(See CLEARING DTC [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].)

•  Disconnect the negative battery cable.

•  Reconnect the negative battery cable.

Note

•  The keyless control module performs on-board self-diagnostics while the negative battery cable is connected.

•  Verify the immobilizer system DTC using the M-MDS.
(See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].)

•  Is the same DTC present?

Yes

Replace the coil antenna, then go to the next step.

(See COIL ANTENNA REMOVAL/INSTALLATION [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].)

No

Go to Step 8.

7

VERIFY TROUBLESHOOTING COMPLETED

•  Make sure to reconnect all disconnected connectors.

•  Reconnect the negative battery cable.

•  Clear the DTC from the keyless control module using the M-MDS.
(See CLEARING DTC [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].)

•  Disconnect the negative battery cable.

•  Reconnect the negative battery cable.

Note

•  The keyless control module performs on-board self-diagnostics while the negative battery cable is connected.

•  Verify the immobilizer system DTC using the M-MDS.
(See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].)

•  Is the same DTC present?

Yes

Replace the keyless control module and program the immobilizer system-related parts.

(See KEYLESS CONTROL MODULE REMOVAL/INSTALLATION [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].)

(See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].)

Go to the next step.

No

Go to the next step.

8

VERIFY THAT NO OTHER DTCs ARE PRESENT

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].)

No

DTC troubleshooting completed.

DTC	Security light flashing pattern		—	Coil antenna power supply circuit malfunction
	M-MDS display	Keyless control module	B10E6:12
	M-MDS display	PCM	—
DETECTION CONDITION				• Voltage higher than the specification (2.2—6.5 V) is detected for 0.05 s while the coil antenna power supply circuit is not active.
POSSIBLE CAUSE				• Coil antenna connector or terminals malfunction • Push button start connector or terminals malfunction • Keyless control module connector or terminals malfunction • Short to power supply in wiring harness between the following terminals: ― Push button start terminal C—Keyless control module terminal 4Q ― Coil antenna terminal A—Keyless control module terminal 4Q ― Coil antenna terminal B—Keyless control module terminal 4Q • Push button start malfunction • Coil antenna malfunction • Keyless control module malfunction

STEP	INSPECTION		ACTION
1	INSPECT COIL ANTENNA CONNECTOR AND TERMINALS • Switch the ignition to off. • Disconnect the negative battery cable. • Disconnect the coil antenna connector. • Inspect the connector and terminals (corrosion, damage, pin disconnection). • Is there any malfunction?	Yes	Repair or replace the connector or terminals, then go to Step 7.
1		No	Go to the next step.
2	INSPECT PUSH BUTTON START CONNECTOR AND TERMINALS • Disconnect the push button start connector. • Inspect the connector and terminals (corrosion, damage, pin disconnection). • Is there any malfunction?	Yes	Repair or replace the connector or terminals, then go to Step 7.
2		No	Go to the next step.
3	INSPECT KEYLESS CONTROL MODULE CONNECTOR AND TERMINALS • Disconnect the keyless control module connector. • Inspect the connector and terminals (corrosion, damage, pin disconnection). • Is there any malfunction?	Yes	Repair or replace the connector or terminals, then go to Step 7.
3		No	Go to the next step.
4	INSPECT COIL ANTENNA POWER SUPPLY CIRCUIT FOR SHORT TO POWER SUPPLY • Coil antenna, push button start and keyless control module connectors are disconnected. • Reconnect the negative battery cable. • Measure the voltage at the keyless control module terminal 4Q (wiring harness-side). • Is the voltage 2.2 V or more?	Yes	Repair or replace the wiring harness for a possible short to power supply, then go to Step 7.
4		No	Go to the next step.
5	INSPECT PUSH BUTTON START • Inspect the push button start. (See PUSH BUTTON START INSPECTION [WITH ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].) • Is there any malfunction?	Yes	Replace the push button start, then go to Step 7. (See PUSH BUTTON START REMOVAL/INSTALLATION [WITH ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].)
5		No	Go to the next step.
6	VERIFY COIL ANTENNA MALFUNCTION • Make sure to reconnect all disconnected connectors. • Reconnect the negative battery cable. • Clear the DTC from the keyless control module using the M-MDS. (See CLEARING DTC [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].) • Disconnect the negative battery cable. • Reconnect the negative battery cable. Note • The keyless control module performs on-board self-diagnostics while the negative battery cable is connected. • Verify the immobilizer system DTC using the M-MDS. (See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].) • Is the same DTC present?	Yes	Replace the coil antenna, then go to the next step. (See COIL ANTENNA REMOVAL/INSTALLATION [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].)
6		No	Go to Step 8.
7	VERIFY TROUBLESHOOTING COMPLETED • Make sure to reconnect all disconnected connectors. • Reconnect the negative battery cable. • Clear the DTC from the keyless control module using the M-MDS. (See CLEARING DTC [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].) • Disconnect the negative battery cable. • Reconnect the negative battery cable. Note • The keyless control module performs on-board self-diagnostics while the negative battery cable is connected. • Verify the immobilizer system DTC using the M-MDS. (See DTC INSPECTION [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].) • Is the same DTC present?	Yes	Replace the keyless control module and program the immobilizer system-related parts. (See KEYLESS CONTROL MODULE REMOVAL/INSTALLATION [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].) (See IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM].) Go to the next step.
7		No	Go to the next step.
8	VERIFY THAT NO OTHER DTCs ARE PRESENT • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)].)
8		No	DTC troubleshooting completed.