DTC P0111:00 [L8, LF, L5]

id010242701300

DTC P0111:00

IAT sensor circuit range/performance problem

DETECTION CONDITION

•  If the intake air temperature is higher than the engine coolant temperature by 40 °C {72 °F} for 60 s with key on, the PCM determines that there is a IAT sensor performance problem.

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.

•  PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle.

•  FREEZE FRAME DATA is available.

•  The DTC is stored in the PCM memory.

POSSIBLE CAUSE

•  IAT sensor malfunction

•  Connector or terminal malfunction

•  PCM malfunction

DTC P0111:00	IAT sensor circuit range/performance problem
DETECTION CONDITION	• If the intake air temperature is higher than the engine coolant temperature by 40 °C {72 °F} for 60 s with key on, the PCM determines that there is a IAT sensor performance problem. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM. • PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle. • FREEZE FRAME DATA is available. • The DTC is stored in the PCM memory.
POSSIBLE CAUSE	• IAT sensor malfunction • Connector or terminal malfunction • PCM malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAS BEEN RECORDED • Has FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT POOR CONNECTION OF MAF/IAT SENSOR CONNECTOR • Switch the ignition to off. • Disconnect the MAF/IAT sensor connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the terminal and/or connector, then go to Step 6.
3		No	Go to the next step.
4	INSPECT IAT SENSOR • Inspect the IAT sensor. (See INTAKE AIR TEMPERATURE (IAT) SENSOR INSPECTION [L8, LF, L5]) • Is the IAT sensor normal?	Yes	Go to the next step.
4		No	Replace the MAF/IAT sensor, then go to Step 6. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L8, LF, L5].)
5	INSPECT POOR CONNECTION OF PCM CONNECTOR • Switch the ignition to off. • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the terminal and/or connector, then go to the next step.
5		No	Go to the next step.
6	VERIFY TROUBLESHOOTING OF DTC P0111:00 COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. • Start the engine and run the engine under FREEZE FRAME DATA condition. • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [L8, LF, L5].)
6		No	Go to the next step.
7	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [L8, LF, L5].) • Are any DTC present?	Yes	Go to the applicable DTC troubleshooting. (See DTC TABLE [L8, LF, L5].)
7		No	Troubleshooting completed.