DTC P2119:00 [L8, LF, L5]

DTC P2119:00	Throttle actuator control throttle body range/performance problem
DETECTION CONDITION	• The PCM compares the TP with the default TP when switch the ignition to off. If the TP is higher than the default TP, the PCM determines that there is a throttle valve actuator control throttle body range/performance problem. Diagnostic support note • This is a continuous monitor (CCM). • MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA is available. • The DTC is stored in the PCM memory.
POSSIBLE CAUSE	• Throttle valve actuator malfunction • Throttle valve malfunction • PCM malfunction

DTC P2119:00

Throttle actuator control throttle body range/performance problem

DETECTION CONDITION

• The PCM compares the TP with the default TP when switch the ignition to off. If the TP is higher than the default TP, the PCM determines that there is a throttle valve actuator control throttle body range/performance problem.

Diagnostic support note

• This is a continuous monitor (CCM).

• MIL illuminates if the PCM detects the above malfunction condition during the first drive cycle.

• FREEZE FRAME DATA is available.

• The DTC is stored in the PCM memory.

POSSIBLE CAUSE

• Throttle valve actuator malfunction

• Throttle valve malfunction

• PCM malfunction

STEP	INSPECTION	ACTION
1	VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAS BEEN RECORDED • Has FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
No	Record the FREEZE FRAME on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service information. If the vehicle is not repaired, go to the next step.
No	Go to the next step.
3	INSPECT THROTTLE VALVE ACTUATOR • Inspect the throttle body. (See THROTTLE BODY INSPECTION [L8, LF, L5].) • Is there any malfunction?	Yes	Replace the throttle body, then go to Step 5. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L8, LF, L5].)
No	Go to the next step.
4	INSPECT THROTTLE VALVE • Inspect the throttle body. (See THROTTLE BODY INSPECTION [L8, LF, L5].) • Is there any malfunction?	Yes	Replace the throttle body, then go to the next step. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L8, LF, L5].)
No	Go to the next step.
5	VERIFY TROUBLESHOOTING OF DTC P2119:00 COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. • Switch the ignition to ON (Engine off), then off. • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [L8, LF, L5].)
No	Go to the next step.
6	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [L8, LF, L5].) • Is any DTC present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [L8, LF, L5].)
No	DTC troubleshooting completed.

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAS BEEN RECORDED

• Has FREEZE FRAME DATA been recorded?

Yes

Go to the next step.

Record the FREEZE FRAME on the repair order, then go to the next step.

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

• Verify related Service Information availability.

• Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service information.

If the vehicle is not repaired, go to the next step.

Go to the next step.

INSPECT THROTTLE VALVE ACTUATOR

• Inspect the throttle body.

(See THROTTLE BODY INSPECTION [L8, LF, L5].)

• Is there any malfunction?

Yes

Replace the throttle body, then go to Step 5.

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L8, LF, L5].)

Go to the next step.

INSPECT THROTTLE VALVE

• Inspect the throttle body.

(See THROTTLE BODY INSPECTION [L8, LF, L5].)

• Is there any malfunction?

Yes

Replace the throttle body, then go to the next step.

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [L8, LF, L5].)

Go to the next step.

VERIFY TROUBLESHOOTING OF DTC P2119:00 COMPLETED

• Make sure to reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS.

• Switch the ignition to ON (Engine off), then off.

• Is the PENDING CODE for this DTC present?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [L8, LF, L5].)

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

• Perform the “AFTER REPAIR PROCEDURE”.

(See AFTER REPAIR PROCEDURE [L8, LF, L5].)

• Is any DTC present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [L8, LF, L5].)

DTC troubleshooting completed.