|
STEP
|
INSPECTION
|
ACTION
|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to next step.
|
|
2
|
VERIFY REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to next step.
|
|
No
|
Go to the next step.
|
|
3
|
INDETIFY TRIGGER DTC FOR FEEZE FRAME DATA
• Is DTC P0403 on FREEZE FRAME DATA?
|
Yes
|
Go to the next step.
|
|
No
|
Go to FREEZE FRAME DATA DTC inspection.
|
|
4
|
PERFORM KEY ON ENGINE OFF (KOEO) SELF TEST
• Perform KOEO self test.
• Is DTC P0403 displayed?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 9.
|
|
5
|
CHECK EGR SOLENOID VALVE RESISTANCE
• Disconnect EGR solenoid valve.
• Measure EGR solenoid valve terminals resistance at the component side connector.
• Is the resistance 26-40 ohms?
|
Yes
|
Go to the next step.
|
|
No
|
Replace EGR solenoid valve, then go to Step 11.
|
|
6
|
CHECK VPWR VOLTAGE TO EGR SOLENOID VALVE
• Turn the ignition switch to ON.
• Measure voltage between EGR solenoid valve terminal 1 and chassis ground.
• Is voltage greater than 10.5 V?
|
Yes
|
Go to the next step.
|
|
No
|
Repair open circuit, then go to Step 11.
|
|
7
|
CHECK EGR SOLENOID VALVE CONTROL CIRCUIT FOR OPEN IN HARNESS
• Disconnect PCM.
• Turn the ignition switch to ON.
• Measure resistance of EGR solenoid valve control circuit between PCM terminal 47 (R.H.D.) /E-27 (L.H.D.) and EGR solenoid valve terminal 2 at harness side connectors.
• Is resistance less than 5.0 ohms?
|
Yes
|
Go to the next step.
|
|
No
|
Repair for open circuit, then go to Step 11.
|
|
8
|
CHECK EGR SOLENOID VALVE CONTROL CIECUIT FOR SHORT TO POWER IN HARNESS
• Turn the ignition switch to ON.
• Measure voltage between PCM harness side connector terminal 47 (R.H.D.) /E-27 (L.H.D.) and battery negative post.
• Is voltage less than 1.0 V?
|
Yes
|
Go to the next step.
|
|
No
|
Replace short to power circuit, then go to Step 11.
|
|
9
|
CHECK EGR SOLENOID VALVE CONTROL CIRCUIT SHORT TO GROUND IN HARNESS
• Measure resistance between terminal 47 (R.H.D.) /E-27 (L.H.D.) and 24, 51, 76, 103 (R.H.D.) /C-48, C-49 (L.H.D.) at PCM harness side connector.
• Is resistance greater than 10,000 ohms?
|
Yes
|
Replace PCM, then go to Step 11.
|
|
No
|
Repair short to ground circuit, then go to Step 11.
|
|
10
|
WIGGLE EGR SOLENOID VALVE WHILE MOITORING VPWR
• Disconnect PCM.
• Turn the ignition switch to ON.
• Measure voltage between EGR solenoid valve terminal 2 and 24, 51, 76, 103 (R.H.D.) /C-48, C-49 (L.H.D.) at PCM harness side connector.
• Voltage must read greater than 10.5 V. For an indication of a fault, look for this voltage to drop while performing the following:
-
- Lightly tap EGR solenoid valve.
-
- Wiggle the EGR solenoid valve connector.
-
- Grasp the EGR solenoid valve harness
• Is a fault indicated?
|
Yes
|
Isolate fault and repair or replace malfunctioning part, then go to the next step.
|
|
No
|
Intermittent concern exists, go to Intermittent Troubleshooting Procedure.
|
|
11
|
VERIFY TROUBLESHOOTING OF DTC P0403 COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the WDS or equivalent.
• Perform KOEO/KOER self test.
• Is the PENDING CODE same DTC present?
|
Yes
|
Replace PCM, then go to next step.
|
|
No
|
Go to the next step.
|
|
12
|
VERIFY AFTER SERVICE PRECAUTION
• Perform "AFTER SERVICE PRECAUTION".
• Is there any DTC present?
|
Yes
|
Go to applicable DTC inspection.
|
|
No
|
Troubleshooting completed.
|