Shift Lock System

SHIFT LOCK SYSTEM

Component Function Check


1. CHECK CVT SHIFT LOCK OPERATION

1.Turn ignition switch ON.
2.Move selector lever to "P" position.
3.Attempt to shift selector lever to any other position with brake pedal released.
Can selector lever be shifted to any other position?
YES- Go to Diagnosis Procedure (see below).
NO- GO TO 2.

2. CHECK CVT SHIFT LOCK OPERATION

Attempt to shift selector lever to any other position with brake pedal depressed.
Can the selector lever be shifted to any other position?
YES- INSPECTION END
NO- Go to Diagnosis Procedure (see below).


Diagnosis Procedure


1. CHECK POWER SOURCE

1.Turn ignition switch OFF.
2.Disconnect the fuse block (J/B) connector.
3.Turn ignition switch ON.
4.Check the voltage between fuse block (J/B) connector terminal and ground.





Is the inspection result normal?
YES- GO TO 2.
NO-Check the following.
- 10A fuse [No. 3, located in fuse block (J/B)]
- Ignition switch

2. CHECK HARNESS BETWEEN FUSE BLOCK (J/B) AND STOP LAMP SWITCH (PART 1)

1.Turn ignition switch OFF.
2.Disconnect the stop lamp switch connector.
3.Check continuity between fuse block (J/B) vehicle side harness connector terminal and stop lamp switch vehicle side harness connector terminal.





Is the inspection result normal?
YES- GO TO 3.
NO- Repair or replace damaged parts.

3. CHECK HARNESS BETWEEN FUSE BLOCK (J/B) AND STOP LAMP SWITCH (PART 2)

Check continuity between stop lamp switch vehicle side harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 4.
NO- Repair or replace damaged parts.

4. CHECK STOP LAMP SWITCH

Check the stop lamp switch. .
Is the inspection result normal?
YES- GO TO 5.
NO- Replace stop lamp switch. Exploded View.

5. CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)

1.Disconnect the CVT shift selector connector.
2.Check the continuity between stop lamp switch vehicle side harness connector terminal and CVT shift selector vehicle side harness connector terminal.





Is the inspection result normal?
YES- GO TO 6.
NO- Repair or replace damaged parts.

6. CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 2)

Check the continuity between control vehicle side harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 7.
NO- Repair or replace damaged parts.

7. CHECK GROUND CIRCUIT

Check the continuity between CVT shift selector vehicle side harness connector terminal and ground.





Is the inspection result normal?
YES- GO TO 8.
NO- Repair or replace damaged parts.

8. CHECK CVT SHIFT SELECTOR

1.Shift selector lever to "P" position.
2.Check the continuity between CVT shift selector connector terminals.





Is the inspection result normal?
YES- GO TO 9.
NO- Replace CVT shift selector. Exploded View.

9. CHECK SHIFT LOCK SOLENOID

1.Remove the shift lock unit. Exploded View.
2.Check the shift lock solenoid. .
Is the inspection result normal?
YES- INSPECTION END
NO- Repair or replace damaged parts.


Component Inspection (Stop Lamp Switch)


1. CHECK STOP LAMP SWITCH

Check the continuity between stop lamp switch connector terminals.





Is the inspection result normal?
YES- INSPECTION END
NO- Replace the stop lamp switch. Exploded View.


Component Inspection (Shift Lock Solenoid)


1. CHECK SHIFT LOCK SOLENOID

Apply voltage to CVT shift selector connector terminals and then check that shift lock solenoid is activated.

CAUTION:
Connect the fuse between the terminals when applying the voltage.





Is the inspection result normal?
YES- INSPECTION END
NO- Replace the shift lock unit. Exploded View.