Part 2

71. Remove the front and rear frame bolts (1, 2).





72. Remove the frame rear strap bolts (2, 3).
73. Remove the frame rear straps (1, 4).
74. Raise the vehicle in order to separate the powertrain/frame assembly from the vehicle.





75. If necessary perform the following steps, remove the engine harness ground wire nut (1).
76. Remove the engine harness positive battery cable (2) from the stud.
77. Disconnect the engine harness electrical connector (3) from the starter.





78. Remove the engine harness ground nuts (1, 2) from the transaxle studs.
79. Remove the engine harness grounds from the studs.
80. Remove the negative battery cable from the transaxle stud.





81. Remove the engine to transaxle brace.





82. Remove the starter motor bolts and starter.





83. Remove the torque converter cover bolts (1, 3).
84. Remove the torque converter covers (2, 4).





85. Use the J 37096 in order to hold the flywheel, and also rotate the flywheel to access the torque converter bolts.





86. Remove the torque converter bolts.





87. Remove the engine mount to frame nuts.





88. Remove the engine harness clips (1) from the transaxle brace.





89. Remove the engine harness clips (1) from the transaxle brace.





90. Remove the transaxle brace bolts and brace.





91. Remove the exhaust crossover pipe shield bolts (1) and shield (2).





92. Remove the exhaust crossover pipe nuts (1) and pipe (2).





93. Disconnect the engine harness electrical connector (1) from the EVAP purge solenoid.
94. Disconnect the engine harness electrical connector (2) from the throttle actuator.





95. Disconnect the engine harness electrical connector (1) from the manifold absolute pressure (MAP) sensor.
96. Disconnect the engine harness electrical connector (2) from the ignition coil.





97. Remove the engine harness clip (1) from the ignition coil bracket.





98. Remove the engine harness clip (1) from he ignition coil bracket.





99. Remove the engine harness clip from the engine.





100. Remove the engine harness bolt.
101. Disconnect the engine harness electrical connector from the camshaft actuator magnet.





102. Remove the engine harness bracket nut (1).
103. Remove the engine harness bracket (2) from the stud.





104. Remove the engine harness clip (1) from the bracket.





105. Disconnect the engine harness electrical connector (1) from the intake manifold tuning valve.
106. Remove the connector position assurance (CPA) retainer (2).
107. Disconnect the engine harness electrical connector (3) from the fuel injector harness electrical connector.





108. Remove the generator terminal nut (1).
109. Remove the engine harness lead (2) from the generator.
110. Disconnect the engine harness electrical connector (3) from the generator.
111. Disconnect the engine harness electrical connector (4) from the heated oxygen sensor (HO2S).





112. Remove the engine harness clip (1) from the strut bracket.





113. Disconnect the engine harness electrical connector (1) from the crankshaft position (CKP) sensor.





114. Disconnect the engine harness electrical connector (1) from the knock sensor.
115. Disconnect the engine harness electrical connector (2) from the oil pressure sensor.





116. Disconnect the engine harness electrical connector from the transaxle.





117. Disconnect the engine harness electrical connector from the vehicle speed sensor (VSS).





118. Remove the engine harness clip (1) from the stud on the transaxle.





119. Remove the engine harness clamp bolt from the transaxle.





120. Remove the engine harness clips (1) from the transaxle studs.





121. Disconnect the engine harness electrical connector from the oil level sensor.





122. Remove the engine harness clip from the oil pan.
123. Gather all branches of the engine harness together and remove the engine harness from the engine.
124. Disconnect the power steering line retainer from the generator bracket.
125. Remove the power steering pressure pipe and return line from the power steering pump and position out of the way.





126. Install an engine hoist to the engine.
127. Remove the transaxle bolts and studs.
128. Support the transaxle.
129. Separate and remove the engine from the transaxle and the frame.





130. Use the J 37096 in order to hold the flywheel.





131. Loosen the flywheel bolts.
132. Remove 5 of the 6 flywheel bolts leaving one bolt at the top of the crankshaft.
133. Grip the flywheel and remove the remaining bolt. Do not drop the flywheel when removing the final bolt.
134. Remove the engine flywheel.
135. Install the engine to the engine stand.
136. Remove the engine hoist from the engine.