Removal
FA20 ENGINE MECHANICAL: CAMSHAFT: REMOVAL; 2013 MY FR-S [03/2012 -]
1. INSTALL ENGINE STAND
Removal
2. REMOVE ENGINE HANGER Removal
3. REMOVE GENERATOR COVER Removal
4. REMOVE BELT GENERATOR COVER Removal
5. REMOVE FAN AND GENERATOR V BELT Removal
6. REMOVE GENERATOR ASSEMBLY Removal
7. REMOVE OIL LEVEL DIPSTICK GUIDE Removal
8. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY Removal
9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY Removal
10. REMOVE INJECTOR COVER (for Bank 1) Removal
11. REMOVE INJECTOR COVER (for Bank 2) Removal
12. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY Removal
13. SEPARATE VENTILATION HOSE Removal
14. REMOVE INTAKE MANIFOLD Removal
15. REMOVE NO. 2 FUEL DELIVERY PIPE Removal
16. REMOVE FUEL PUMP ASSEMBLY Removal
17. REMOVE VALVE LIFTER Removal
18. REMOVE PUMP DRIVE CASE ASSEMBLY Removal
19. REMOVE VACUUM PUMP ASSEMBLY (for Automatic Transmission) Removal
20. REMOVE REAR CYLINDER HEAD PLATE (for Manual Transmission) Disassembly
21. REMOVE NO. 1 WATER BY-PASS PIPE (for Automatic Transmission) Removal
22. REMOVE NO. 1 WATER BY-PASS PIPE (for Manual Transmission) Removal
23. REMOVE CRANKSHAFT PULLEY Removal
24. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL Removal
25. DISCONNECT ENGINE WIRE Removal
26. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY Removal
27. REMOVE CHAIN SUB-ASSEMBLY (for Bank 1) Disassembly
28. REMOVE CHAIN SUB-ASSEMBLY (for Bank 2) Disassembly
29. ROTATE CRANKSHAFT AND CAMSHAFT
(a) Turn the crankshaft approximately 200° clockwise, and align the alignment mark as shown in the illustration.
NOTICE:
Do not turn the crankshaft counterclockwise except for a slight adjustment to correctly align the alignment mark. If not, the valves may come into contact with the piston.
(b) Using SST, turn the camshaft timing intake gear assembly LH approximately 180°clockwise, and align the alignment mark on the camshaft timing intake gear assembly LH to the position (zero-lift position) shown in the illustration.
SST : 09960-10010
09962-01000
09963-00700
NOTICE:
After this work, when the intake valve and exhaust valve lift at the same time, the valve heads contact each other, causing the valve stems to bend. To avoid this, do not turn the intake camshaft LH and the exhaust camshaft LH more than the zero-lift range (the range where the camshafts can be turned lightly by hand).
(c) Remove the pulley bolt.
30. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET Disassembly
31. REMOVE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY RH
(a) Using SST, hold the camshaft timing intake gear assembly RH and remove the 3 bolts with a "TORX" socket wrench E16.
SST : 09960-10010
09962-01000
09963-00700
(b) Remove the camshaft timing intake gear assembly RH.
32. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH
(a) Using SST, hold the camshaft timing exhaust gear assembly RH and remove the 3 bolts with a "TORX" socket wrench E16.
SST : 09960-10010
09962-01000
09963-00700
(b) Remove the camshaft timing exhaust gear assembly RH.
33. REMOVE CAMSHAFT TIMING INTAKE GEAR ASSEMBLY LH
(a) Using SST, hold the camshaft timing intake gear assembly LH and remove the 3 bolts with a "TORX" socket wrench E16.
SST : 09960-10010
09962-01000
09963-00700
(b) Remove the camshaft timing intake gear assembly LH.
34. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH
(a) Using SST, hold the camshaft timing exhaust gear assembly LH and remove the 3 bolts with a "TORX" socket wrench E16.
SST : 09960-10010
09962-01000
09963-00700
(b) Remove the camshaft timing exhaust gear assembly LH.
35. REMOVE IGNITION COIL ASSEMBLY (for Bank 2) Removal
36. REMOVE SPARK PLUG (for Bank 2) Removal
37. REMOVE IGNITION COIL ASSEMBLY (for Bank 1) Removal
38. REMOVE SPARK PLUG (for Bank 1) Removal
39. REMOVE INJECTOR DRIVER BRACKET Disassembly
40. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH Disassembly
41. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH Disassembly
42. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH Disassembly
43. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH Disassembly
44. REMOVE CAMSHAFT CAP (for Bank 1)
(a) In several steps, uniformly loosen the 12 bolts in the order shown in the illustration, and remove the front camshaft cap RH, intake center camshaft cap RH, intake rear camshaft cap RH, exhaust center camshaft cap RH, and exhaust rear camshaft cap RH.
HINT
Arrange the removed parts in the correct order.
45. REMOVE CAMSHAFT RH (for Bank 1)
(a) Remove the intake camshaft RH and exhaust camshaft RH from the camshaft housing sub-assembly RH.
46. REMOVE CAMSHAFT CAP (for Bank 2)
(a) In several steps, uniformly loosen the 13 bolts in the order shown in the illustration, and remove the front camshaft cap LH, intake center camshaft cap LH, intake rear camshaft cap LH, exhaust center camshaft cap LH and exhaust rear camshaft cap LH.
HINT
Arrange the removed parts in the correct order.
47. REMOVE CAMSHAFT LH (for Bank 2)
(a) Remove the intake camshaft LH and exhaust camshaft LH from the camshaft housing sub-assembly LH.