Front Seat (Bench Type)
DISASSEMBLY1. REMOVE HEADRESTS
2. REMOVE SEAT CUSHION OUTER SHIELD
Remove the screw and seat cushion outer shield.
3. REMOVE SEAT CUSHION INNER SHIELD
Remove the screw and seat cushion inner shield.
4. REMOVE SEATBACK ASSEMBLY
a. Remove the nut from rear side of the seat cushion.
b. Remove the 2 bolts and seatback assembly.
5. REMOVE SEATBACK FRAME
a. Remove the hog rings.
b. Remove the 4 headrest supports.
c. Remove the seatback frame from the seatback cover with pad.
6. REMOVE SEATBACK COVER
Remove the hog rings and seatback cover from the seatback pad.
7. REMOVE ARMREST
Remove the 2 nuts and armrest from the seatback frame.
8. REMOVE SEAT CUSHION ASSEMBLY
Remove the 4 bolts and seat cushion assembly from the seat adjusters.
9. REMOVE SEAT CUSHION FRAME
a. Remove the screw and cushion.
b. Employ the same manner described above to the other side.
c. Remove the hog rings and unlatch the seat cushion cover.
d. Remove the seat cushion frame from the seat cushion cover with pad.
10. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from seat cushion pad.
11. REMOVE SPACERS
Remove the 2 bolts and 2 spacers from the seat cushion frame.
12. REMOVE EQUALIZING WIRE
a. Disconnect the equalizing wire from the seat adjuster LH as shown in the illustration
b. Using a screwdriver, unstake the claws.
HINT: Tape the screwdriver tip before use.
c. Loosen the adjusting nuts.
HINT: When loosening the nuts, while holding one nut, loosen the other.
d. Disconnect the equalizing wire from the seat adjuster RH as shown in the illustration.
REASSEMBLY
1. INSTALL EQUALIZING WIRE
a. Connect the equalizing wire to the seat adjuster RH as shown in the illustration.
b. Tighten the adjusting nuts.
HINT: When tighten the nuts, while holding one nuts, tighten the other.
c. Stake the claws.
d. Connect the equalizing wire to the seat adjuster LH as shown in the illustration.
2. INSTALL SPACERS
Install the 2 spacers with the 2 bolts to the seat cushion frame.
Torque: 47 N.m (479 kgf.cm, 35 ft.lbf)
3. INSTALL SEAT CUSHION COVER
Install the seat cushion cover with new hog rings to the seat cushion pad.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
4. INSTALL SEAT CUSHION FRAME
a. Install the seat cushion frame to the seat cushion cover with pad.
b. Install the seat cushion frame with new hog rings and latch the seat cushion cover hooks.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
c. Install the cushion with the screw.
HINT: Employ the same manner described above to the other side.
5. INSTALL SEAT CUSHION ASSEMBLY
Install the seat cushion assembly with the 4 bolts to the seat adjusters.
Torque: 18 N.m (185 kgf.cm, 13 ft.lbf)
6. INSTALL ARMREST
Install the armrest with the 2 nuts to the seatback frame.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
7. INSTALL SEATBACK COVER
Install the seatback cover with new hog rings to the seatback pad.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
8. INSTALL SEATBACK FRAME
a. Install the seatback frame to the seatback cover with pad.
b. Install the 4 headrest supports.
c. Install the new hog rings as shown in the illustration.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
9. INSTALL SEATBACK ASSEMBLY
a. Install the seatback assembly with the 2 bolts.
Torque: 39 N.m (400 kgf.cm, 29 ft.lbf)
b. Install the nut to the rear side of the seat cushion.
Torque: 18 N.m (185 kgf.cm, 13 ft.lbf)
10. INSTALL SEAT CUSHION INNER SHIELD
Install the seat cushion inner shield with the screw.
11. INSTALL HEADRESTS