Front Seat (Separate Type: Manual Adjuster)

DISASSEMBLY

1. REMOVE HEADREST
2. REMOVE VERTICAL ADJUSTER KNOB
Using a screwdriver, remove the snap ring and vertical adjuster knob.

HINT: Tape the screwdriver tip before use.




3. REMOVE RECLINING ADJUSTER RELEASE HANDLE




4. REMOVE FRONT SEAT CUSHION SHIELD
Remove the 2 screws and front seat cushion shield.




5. REMOVE FRONT SEAT CUSHION INNER SHIELD
Remove the 2 screws and front seat cushion inner shield.

6. REMOVE FRONT SEAT INNER BELT
Unfasten the bolt and front seat inner belt.

7. REMOVE SEAT CUSHION ASSEMBLY
Remove the 4 bolts and seat cushion assembly.

8. REMOVE SEAT CUSHION COVER




a. Unlatch the seat cushion cover hooks, then remove the seat cushion frame from seat cushion cover with pad.




b. Remove the 12 hog rings and seat cushion cover from the seat cushion pad.

9. REMOVE SEATBACK ASSEMBLY




a. Remove the 3 hog rings shown in the illustration.
b. Remove the 4 bolts and seatback assembly.

10. REMOVE ARMREST
a. Open the fastener.
b. Remove the bolt and armrest.
c. Remove the armrest cover.

11. REMOVE SEATBACK FRAME
a. Turn over the seatback cover upward.




b. Remove the 2 hog rings as shown in the illustration.
c. Remove the 2 headrest supports.




d. Remove the 2 hog rings and seatback cover from the seatback pad with frame.
e. Remove the seatback frame from the seatback pad.

12. REMOVE SEAT TRACK HANDLE
Using a screwdriver, remove the seat track handle.

HINT: Tape the screwdriver tip before use.

13. DISASSEMBLE OUTER TRACK AND INNER TRACK
a. Using a screwdriver, remove the E-ring from the outer side on the inner track.

HINT: Tape the screwdriver tip before use.

b. Disassemble the outer track and inner track.

14. REMOVE RECLINING CONNECTING PIPE
15. REMOVE SEAT CUSHION INSIDE COVERS
a. Remove the screw and seat cushion inside cover RH.
b. Remove the screw and seat cushion inside cover LH.

REASSEMBLY

1. INSTALL SEAT CUSHION INSIDE COVERS
a. Install the seat cushion inside cover RH with the screw.
b. Install the seat cushion inside cover LH with the screw.

2. INSTALL RECLINING CONNECTING PIPE




a. Adjust the reclining lock positions of the seat adjusters.
b. Slide the seat adjusters to the most front position.
c. Place the adjusters on a spacer to adjust the seat rails in parallel and install the connecting pipe.

HINT: When installing the connecting pipe while raising up the adjusters, the lock positions adjusted in 2-(a) step slip off then lock error will occur.

3. ASSEMBLE OUTER TRACK AND INNER TRACK
a. Assemble the outer track and inner track.
b. Install the E-ring to the outer side on the inner track.

4. INSTALL SEAT TRACK HANDLE
5. INSTALL SEATBACK FRAME
a. Install the seatback frame to the seatback pad.
b. Put the seatback cover on the seatback frame with pad.
c. Install the 2 headrest supports.




d. Install 2 new hog rings as shown in the illustration.

HINT: When installing hog rings, take care to prevent wrinkles as much as possible.




e. Install 2 new hog rings as shown in the illustration.

HINT: When installing hog rings, take care to prevent wrinkles as much as possible.

f. Put the seatback cover on the seatback frame with pad.

6. INSTALL ARMREST
a. Install the armrest cover.
b. Install the armrest with the bolt.

Torque: 37 N.m (375 kgf.cm, 27 ft.lbf)

c. Close the fastener.

7. INSTALL SEATBACK ASSEMBLY
a. Install the seatback assembly with the 4 bolts.

Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)




b. Install 3 new hog rings as shown in the illustration.

HINT: When installing hog rings, take care to prevent wrinkles as much as possible.

8. INSTALL SEAT CUSHION COVER




a. Install the seat cushion cover with new hog rings to the seat cushion pad.

HINT: When installing hog rings, take care to prevent wrinkles as much as possible.

b. Install the seat cushion frame to the seat cushion pad with cover.




c. Latch the seat cushion cover hooks.

9. INSTALL SEAT CUSHION ASSEMBLY
Install the seat cushion assembly with the 4 bolts.

Torque: 19 N.m (195 kgf.cm, 14 ft.lbf)

10. INSTALL FRONT SEAT INNER BELT
Install the front seat inner belt with the bolt.

Torque: 41 N.m (420 kgf.cm, 30 ft.lbf)




11. INSTALL FRONT SEAT CUSHION INNER SHIELD
Install the front seat cushion inner shield with the 2 screws.




12. INSTALL FRONT SEAT CUSHION OUTER SHIELD
Install the front seat cushion outer shield with the 2 screws.




13. INSTALL RECLINING RELEASE LEVER
14. INSTALL VERTICAL ADJUSTER KNOB
Install the vertical adjuster knob with the snap ring.

15. INSTALL HEADREST