Part 2

INTERIOR: ROOF HEADLINING: INSTALLATION (Continued)

51. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

(a) Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.





52. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)

(a) Engage the 10 claws and install the side trim cover LH.





53. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)

(a) Connect each connector.





(b) Engage the 4 claws and install the power outlet socket bezel.





54. INSTALL DECK SIDE TRIM LH

(a) Engage the 3 guides and 4 claws as shown in the illustration.





(b) Install the deck side trim LH with the bolt.





55. INSTALL DECK SIDE TRIM COVER LH

(a) Engage the 2 claws and install the deck side trim cover LH.





56. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

HINT
Use the same procedure for the RH side and the LH side.

57. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT
Use the same procedure for the RH side and the LH side.

58. INSTALL QUARTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

59. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

(a) Engage the 4 clips and the 7 claws.

(b) Install the 2 clips.

(c) Install the deck trim side panel assembly RH with the 3 bolts.





60. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

61. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT
Use the same procedure for the RH side and the LH side.

62. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

63. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT
Use the same procedure for the RH side and the LH side.

64. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

(a) Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.





65. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System) Installation

66. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

(a) Engage the 4 claws, and install the side trim cover RH.





67. INSTALL DECK SIDE TRIM RH

HINT
Use the same procedure for the RH side and the LH side.

68. INSTALL DECK SIDE TRIM COVER RH

HINT
Use the same procedure for the RH side and the LH side.

69. INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)

(a) Engage the guide and the 8 claws, and install the rear seat side garnish cap.





70. INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)

(a) Engage the guide and the 6 claws.





(b) Install the rear seat side garnish cap with the screw.

71. INSTALL REAR FLOOR FINISH PLATE

(a) Engage the 4 clips and the 4 claws, and install the rear floor finish plate.





72. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) Installation

73. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat) Installation

74. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat) Installation

75. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat) Installation

76. INSTALL NO. 1 DECK BOARD (w/o Rear No. 2 Seat)

(a) Engage the 3 clips and install the rear floor board spacer to the No. 1 deck board.





77. INSTALL NO. 1 DECK BOARD (w/ Rear No. 2 Seat)

(a) Engage the 5 clips and install the deck floor box to the No. 1 deck board.





78. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

(a) Install the rear deck floor box with the 2 nuts.





79. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

(a) Install the rear deck floor board assembly with the 4 nuts and 4 bolts.





80. INSTALL REAR MAT

(a) Install the rear mat.





81. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

(a) Install the 2 nuts and the deck floor board assembly.





(b) Engage the 3 claws.

82. INSTALL DECK SIDE TRIM BOX LH

(a) Install the deck side trim box LH as shown in the illustration.





(b) Install the 2 deck side trim clip and the clips.





83. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

(a) Engage the 2 clips and install the rear seat side cover LH.





84. INSTALL DECK SIDE TRIM BOX RH

(a) Install the deck side trim box RH as shown in the illustration.





(b) Install the 2 deck side trim clip and the clip.





85. INSTALL JACK CARRIER ASSEMBLY

(a) Engage the 3 claws, and install the jack carrier assembly.





86. INSTALL JACK ASSEMBLY

(a) Install the jack assembly.





87. INSTALL JACK CARRIER CUSHION

(a) Install the jack carrier cushion.





88. INSTALL JACK CARRIER SUPPORT

89. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

(a) Engage the 2 clips and install the rear seat side cover RH.





90. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

(a) Engage the 3 guides and 3 clips and install the rear No. 1 floor board.





91. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

(a) Install the tonneau cover assembly.

92. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

(a) Engage the 2 guides and install the No. 2 deck board sub-assembly.





93. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

(a) Engage the 2 guides and install the No. 3 deck board sub-assembly.





94. INSTALL DECK BOARD ASSEMBLY

(a) Install the deck board sub-assembly.





95. INSTALL CENTER PILLAR GARNISH LH

(a) Engage the 2 guides and the clip.





(b) Install the center pillar garnish LH with the clip and screw.

96. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation

97. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.





98. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.





NOTICE:
After installation, check that the corners fit correctly.

99. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.





100. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.





(b) Install a new clip [A] on the front pillar garnish LH.





(c) Engage the 3 guides and 2 clips, then install the front pillar garnish LH.

101. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.





NOTICE:
After installation, check that the corners fit correctly.

102. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Engage the claw and clip, install the cowl side trim sub-assembly LH.





(b) Install the clip.

103. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the guide and the 8 claws, and install the front door scuff plate LH.





104. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

105. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

106. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

107. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.





NOTICE:
After installation, check that the corners fit correctly.

108. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

109. INSTALL FRONT PILLAR GARNISH RH

(a) Remove the protective cover.





(b) Install a new clip [A] on the front pillar garnish RH.





(c) Engage the 3 guides and 2 clips, then install the front pillar garnish RH.

110. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.





NOTICE:
After installation, check that the corners fit correctly.

111. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

112. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

113. INSTALL REAR NO. 1 SEAT ASSEMBLY LH Installation

114. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function) Installation

115. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side) Installation

116. INSTALL REAR SEAT LEG SIDE COVER LH Installation

117. INSTALL REAR INNER TRACK BRACKET COVER LH Installation

118. INSTALL REAR OUTER TRACK BRACKET COVER LH Installation

119. INSTALL REAR SEAT TRACK BRACKET COVER LH Installation

120. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side) Installation

121. INSTALL REAR CENTER SEAT ASSEMBLY

122. INSTALL REAR NO. 1 SEAT ASSEMBLY RH Installation

123. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT
Use the same procedure for the RH side and the LH side.

124. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side) Installation

125. INSTALL REAR SEAT LEG SIDE COVER RH Installation

126. INSTALL REAR INNER TRACK BRACKET COVER RH Installation

127. INSTALL REAR OUTER TRACK BRACKET COVER RH Installation

128. INSTALL REAR SEAT TRACK BRACKET COVER RH Installation

129. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side) Installation