Reassembly

SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REASSEMBLY

1. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)

(a) Engage the each clamps and install the front seat wire RH.

2. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) Installation

3. INSTALL SEAT POSITION SENSOR Installation

4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (for Front Passenger Side)

(a) w/ Seat Heater System:

Engage the 2 clamps and install the seat heater control sub-assembly.





5. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

(a) Engage the guide and the claw.





(b) Install the front seat lower cushion shield RH with the screw.

6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

(a) Engage the claw.





(b) Install the front seat lower cushion shield LH with the screw.

7. INSTALL RECLINING ADJUSTER INSIDE COVER RH

(a) Engage the claw.





(b) Install the reclining adjuster inside cover RH with the screw.

8. INSTALL RECLINING ADJUSTER INSIDE COVER RH

(a) Engage the guide.





(b) Install the reclining adjuster inside cover RH with the screw.

9. INSTALL RECLINING ADJUSTER INSIDE COVER LH

(a) Engage the claw.





(b) Install the reclining adjuster inside cover LH with the screw.

10. INSTALL RECLINING ADJUSTER INSIDE COVER LH

(a) Engage the guide.





(b) Engage the clamp.

(c) Install the reclining adjuster inside cover LH with the screw.

11. INSTALL ACTIVE HEADREST LOWER UNIT

(a) Install the active headrest lower unit with the 4 nuts.





Torque : 8.5 Nm (87 kgf-cm, 75 in-lbf)

12. INSTALL ACTIVE HEADREST UPPER UNIT

(a) Install the active headrest upper unit with the 4 nuts.





Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

(b) Connect the cable to the active headrest upper unit with the nut as shown in the illustration.

Torque : 8.5 Nm (87 kgf-cm, 75 in-lbf)

13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

(a) Using hog ring pliers, install the separate type front seatback cover with 7 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
14. INSTALL FRONT SEATBACK COVER WITH PAD

(a) Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.

(b) Engage the 4 claws and install the 2 front seat headrest supports.





(c) Install the front seatback cover bracket with the nut.





Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

NOTICE:
* For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
* Check that the strap is not twisted after installing the bracket.
* Install the bracket securely.
(d) Using hog ring pliers, install 5 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(e) Using hog ring pliers, install the front seatback cover with pad with 3 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

(a) Using hog ring pliers, install the separate type front seat cushion cover with 11 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) Using hog ring pliers, install the separate type front seat cushion cover with 6 new hog rings.





16. INSTALL FRONT SEAT CUSHION COVER WITH PAD

(a) Temporarily install the front seat cushion cover with pad to the front seat frame assembly with adjuster.

(b) Engage the hooks.





(c) Install the front seat cushion cover with pad with the 2 clips.

(d) for Front Passenger Side:

(1) w/ Seat Heater System:

Connect the seat heater connector.

(e) Engage the clamp.





17. INSTALL FRONT SEAT CUSHION INNER SHIELD

(a) Insert the guide and temporarily install the front seat cushion inner shield.





(b) Engage the claw.





(c) Install the front seat cushion inner shield with the screw.

18. INSTALL FRONT SEAT INNER BELT ASSEMBLY Installation

19. INSTALL FRONT SEAT CUSHION SHIELD

(a) Engage the 2 guides.





(b) Engage the claw.

(c) Install the front seat cushion shield with the 3 screws.

(d) Engage the hooks.





20. INSTALL VERTICAL ADJUSTING HANDLE

(a) Install the vertical adjusting handle with the 2 screws.





21. INSTALL VERTICAL ADJUSTER COVER

(a) Engage the 2 claws and install the vertical adjuster cover.





22. INSTALL RECLINING ADJUSTER RELEASE HANDLE

(a) Engage the claw and install the reclining adjuster release handle.





23. INSTALL VERTICAL SEAT ADJUSTER KNOB

(a) Install the snap ring to the vertical seat adjuster knob as shown in the illustration.





(b) Install the vertical seat adjuster knob.