Part 2

HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM: P0AA6-526,P0AA6-611,P0AA6-612,P0AA6-613,P0AA6-614: Hybrid Battery Voltage System Isolation Fault
P0AA6-614 - Hybrid Battery Voltage System Isolation Fault

Continued

(e) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Result:

B -- CHECK MOTOR CABLE

A -- REPLACE INVERTER WITH CONVERTER ASSEMBLY Components

10. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE)

CAUTION:
Be sure to wear insulated gloves.

(a) Turn the power switch off.

(b) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(c) Remove the inverter terminal cover from the inverter with converter assembly.

HINT
Make sure that no foreign objects have entered or contaminated the inverter with converter assembly.

(d) Disconnect the motor cable e1 and generator cable f1 from the inverter with converter assembly.

(e) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- CHECK MOTOR CABLE
OK -- Continue to next step.

11. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE)

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- CHECK GENERATOR CABLE
OK -- Continue to next step.

12. CHECK HIGH VOLTAGE DIRECT CURRENT AREA

CAUTION:
Be sure to wear insulated gloves.

(a) Turn the power switch off.

(b) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(c) Disconnect the frame wire T1 from the inverter with converter assembly.

HINT
Make sure that no foreign objects have entered or contaminated the connector of the frame wire T1.

(d) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- CHECK FRAME WIRE
OK -- Continue to next step.

13. CHECK NO. 2 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the No. 2 engine wire (air conditioning harness) E2 from the inverter with converter assembly.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- CHECK NO. 2 ENGINE WIRE

OK -- REPLACE INVERTER WITH CONVERTER ASSEMBLY Components

14. CHECK NO. 2 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the No. 2 engine wire (air conditioning harness) E1 from the compressor with motor assembly.

Text in Illustration

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE NO. 2 ENGINE WIRE

OK -- AIR CONDITIONING SYSTEM (P0AA6-611) P0AA6

15. CHECK FRAME WIRE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the frame wire T4 and T3 from the hybrid battery junction block.

HINT
For the removal and installation procedures related to the frame wire, Components.

(c) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

NG -- REPLACE FRAME WIRE Components

OK -- REPLACE HYBRID BATTERY JUNCTION BLOCK Components

16. CHECK HYBRID BATTERY JUNCTION BLOCK

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the high voltage cable connector of the HV battery h2 and k2 from the hybrid battery junction block.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

NG -- REPLACE HYBRID BATTERY JUNCTION BLOCK Components

OK -- REPLACE HV BATTERY Components

17. CHECK MOTOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Turn the power switch off.

(b) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(c) Disconnect the motor cable from the hybrid vehicle transaxle assembly Components.

(d) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE MOTOR CABLE Components

OK -- REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY Components

18. CHECK GENERATOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the generator cable from the hybrid vehicle transaxle assembly Components.

(c) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE GENERATOR CABLE Components

OK -- REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY Components

19. CHECK MOTOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Turn the power switch off.

(b) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(c) Disconnect the motor cable from the hybrid vehicle transaxle assembly Components.

(d) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE MOTOR CABLE Components
OK -- Continue to next step.

20. CHECK GENERATOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the generator cable from the hybrid vehicle transaxle assembly Components.

(c) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE GENERATOR CABLE Components

OK -- REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY Components