Mirror Heater Does Not Operate With Rear Defogger Switch
MIRROR (EXT): POWER MIRROR CONTROL SYSTEM: Mirror Heater does not Operate with Rear Defogger Switch
- Mirror Heater does not Operate with Rear Defogger Switch
DESCRIPTION
When the rear window defogger switch on the air conditioning control panel assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly through a LIN communication line. When the air conditioning amplifier assembly receives the signal, it turns on the integration relay to operate the mirror heater.
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
1. PERFORM ACTIVE TEST USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical /Air Conditioner / Active Test.
(e) Perform an Active Test according to the display on the Techstream.
Result:
C -- CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
B -- CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
A -- Continue to next step.
2. CHECK DEFOGGER SYSTEM
(a) Check the rear window defogger operation.
OK:
The rear window defogger operated normally.
NG -- GO TO WINDOW DEFOGGER SYSTEM
OK -- Continue to next step.
3. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BODY GROUND)
(a) Disconnect the integration relay connector.
(b) Measure the resistance according to the value(s) in the table below
Standard Resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
4. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - INTEGRATION RELAY)
(a) Disconnect the integration relay connector.
(b) Disconnect the outer rear view mirror assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
5. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - INTEGRATION RELAY)
(a) Disconnect the integration relay connector.
(b) Disconnect the outer rear view mirror assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
6. REPLACE INTEGRATION NO.1 RELAY
(a) Replace the integration relay Removal.
OK -- Continue to next step.
7. CHECK REAR WINDOW DEFOGGER AND MIRROR HEATER
(a) Check the mirror heater system.
OK:
Mirror heater system is normal.
NG -- REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
OK -- END (INTEGRATION RELAY WAS DEFECTIVE)
8. GO TO WINDOW DEFOGGER SYSTEM Problem Symptoms Table
9. REPAIR OR REPLACE HARNESS OR CONNECTOR
10. REPAIR OR REPLACE HARNESS OR CONNECTOR
11. REPAIR OR REPLACE HARNESS OR CONNECTOR
12. REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Removal
13. END (INTEGRATION RELAY WAS DEFECTIVE)
14. CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
(a) Remove the outer mirror rear view mirror assembly RH Removal.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (FRONT PASSENGER SIDE)
OK -- REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH)
15. REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (FRONT PASSENGER SIDE) Removal
16. CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
(a) Remove the outer mirror rear view mirror assembly LH Removal.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (DRIVER SIDE)
OK -- REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH)
17. REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (DRIVER SIDE) Removal
18. REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH)
19. REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH)