B1638

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1628/82,B1637/82,B1638/82,B1647/82: Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete


DESCRIPTION

The side airbag sensor RH consists of parts including the diagnostic circuit and the lateral deceleration sensor.

When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.

DTC B1628/82, B1637/82, B1638/82 or B1647/82 is set when a malfunction is detected in the side airbag sensor RH circuit.





WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK CONNECTION OF CONNECTOR

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor RH and the side airbag sensor RH.

OK:

The connectors are properly connected.

NG -- CONNECT CONNECTOR
OK -- Continue to next step.

2. CHECK FLOOR WIRE NO. 2 (OPEN)





(a) Disconnect the connectors from the center airbag sensor and the side airbag sensor RH.

(b) Using a service wire, connect L10-4 (BBR+) and L10-3 (BBR-) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

3. CHECK FLOOR WIRE NO. 2 (SHORT)





(a) Disconnect the service wire from connector C.

(b) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

4. CHECK FLOOR WIRE NO. 2 (TO B+)





(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

(c) Measure the voltage of the wire harness side connector.

Standard voltage:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

5. CHECK FLOOR WIRE NO. 2 (TO GROUND)





(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

6. CHECK FLOOR WIRE NO. 2 (OPEN)





(a) Disconnect the connectors from the side airbag sensor RH and the rear airbag sensor RH.

(b) Using a service wire, connect L12-1 (BCR-) and L12-2 (BCR+) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

7. CHECK FLOOR WIRE NO. 2 (SHORT)





(a) Disconnect the service wire from connector C.

(b) Measure the resistance of the wire harness side connectors.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

8. CHECK FLOOR WIRE NO. 2 (TO B+)





(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

(c) Measure the voltage of the wire harness side connector.

Standard voltage:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

9. CHECK FLOOR WIRE NO. 2 (TO GROUND)





(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

10. CHECK SIDE AIRBAG SENSOR RH





(a) Connect the connectors to the center airbag sensor.

(b) Interchange the side airbag sensor LH with the side airbag sensor RH and connect the connectors to them.

(c) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs DTC Check / Clear.

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs DTC Check / Clear.

Result





HINT
DTCs other than DTC B1623/81, B1632/81, B1633/81, B1642/81, B1628/82, B1637/82, B1638/82 and B1647/82 may be output at this time, but they are not related to this check.

C -- REPLACE SIDE AIRBAG SENSOR RH

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
A -- Continue to next step.

11. CHECK REAR AIRBAG SENSOR RH





(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.

(d) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(e) Turn the ignition switch to ON, and wait for at least 60 seconds.

(f) Clear the DTCs DTC Check / Clear.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check the DTCs DTC Check / Clear.

Result





HINT
DTCs other than DTC B1623/81, B1632/81, B1633/81, B1642/81, B1628/82, B1637/82, B1638/82 and B1647/82 may be output at this time, but they are not related to this check.

C -- REPLACE REAR AIRBAG SENSOR RH

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY

A -- USE SIMULATION METHOD TO CHECK