B1643

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1643/81: Driver Side Satellite Sensor Bus Initialization Incomplete
B1643/81 - Driver Side Satellite Sensor Bus Initialization Incomplete

DESCRIPTION

The side airbag sensor LH consists of part including the diagnostic circuit and the lateral deceleration sensor.

When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.

DTC B1643/81 is set when a malfunction is detected in the side airbag sensor LH circuit.





WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK FOR DTC





(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

(b) Clear the DTCs DTC Check / Clear.

(c) Turn the ignition switch off.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Check the DTCs DTC Check / Clear.

OK:

DTC B1622/81 is not output.

DTC B1632/81 is not output.

HINT
DTCs other than DTC B1622/81 and B1632/81 may be output at this time, but they are not related to this check.

NG -- GO TO DTC OUTPUT
OK -- Continue to next step.

2. CHECK CONNECTION OF CONNECTOR

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) terminal battery, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor LH and the side airbag sensor LH.

OK:

The connectors are properly connected.

NG -- CONNECT CONNECTOR
OK -- Continue to next step.

3. CHECK FLOOR WIRE (OPEN)





(a) Disconnect the connectors from the center airbag sensor and the side airbag sensor LH.

(b) Using a service wire, connect K9-4 (BBL+) and K9-3 (BBL-) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

4. CHECK FLOOR WIRE (SHORT)





(a) Disconnect the service wire from connector C.

(b) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

5. CHECK FLOOR WIRE (TO B+)





(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

(c) Measure the voltage of the wire harness side connector.

Standard voltage:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

6. CHECK FLOOR WIRE (TO GROUND)





(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

7. CHECK FLOOR WIRE (OPEN)





(a) Disconnect the connectors from the side airbag sensor LH and the rear airbag sensor LH.

(b) Using a service wire, connect K11-1 (BCL-) and K11-2 (BCL+) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

8. CHECK FLOOR WIRE (SHORT)





(a) Disconnect the service wire from connector C.

(b) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

9. CHECK FLOOR WIRE (TO B+)





(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

(c) Measure the voltage of the wire harness side connector.

Standard voltage:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

10. CHECK FLOOR WIRE (TO GROUND)





(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.

11. CHECK SIDE AIRBAG SENSOR LH





(a) Connect the connectors to the center airbag sensor.

(b) Interchange the side airbag sensor LH with the side airbag sensor RH and connect the connectors to them.

(c) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs DTC Check / Clear.

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check the DTCs DTC Check / Clear.

Result





HINT
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.

C -- REPLACE SIDE AIRBAG SENSOR LH

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
A -- Continue to next step.

12. CHECK REAR AIRBAG SENSOR LH





(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) terminal battery, and wait for at least 90 seconds.

(c) Interchange the rear airbag sensor LH with the rear airbag sensor RH and connect the connectors to them.

(d) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(e) Turn the ignition switch to ON, and wait for at least 60 seconds.

(f) Clear the DTCs DTC Check / Clear.

(g) Turn the ignition switch off.

(h) Turn the ignition switch to ON, and wait for at least 60 seconds.

(i) Check the DTCs DTC Check / Clear.

Result





HINT
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.

C -- REPLACE REAR AIRBAG SENSOR LH

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY

A -- USE SIMULATION METHOD TO CHECK