DTC 74

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1905/74-B1908/74: Short in Front Passenger Side Pretensioner Squib Circuit
B1908/74 - Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit

DESCRIPTION

The front passenger side front pretensioner squib circuit consists of the center airbag sensor and the front seat outer belt RH.

This circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side front pretensioner squib circuit.





WIRING DIAGRAM





INSPECTION PROCEDURE

HINT
* Perform the simulation method by selecting the "CHECK MODE" (signal check) with the Techstream Check Mode Procedure.
* After selecting the "CHECK MODE" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads Check Mode Procedure.

PROCEDURE

1. CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB)





(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Disconnect the connectors from the front seat outer belt RH.

(d) Connect SST (resistance 2.1 Ohms) to connector C.

CAUTION:
Never connect a tester to the front seat outer belt RH (front passenger side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
* Do not forcibly insert SST into the terminals of the connector when connecting.
* Insert SST straight into the terminals of the connector.

SST : 09843-18061

(e) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(f) Turn the ignition switch to ON, and wait for at least 60 seconds.

(g) Clear the DTCs DTC Check / Clear.

(h) Turn the ignition switch off.

(i) Turn the ignition switch to ON, and wait for at least 60 seconds.

(j) Check the DTCs DTC Check / Clear.

OK:

DTC B1905, B1906, B1907, B1908 or 74 is not output.

HINT
DTCs other than DTC B1905, B1906, B1907, B1908 or 74 may be output at this time, but they are not related to this check.

OK -- REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH
NG -- Continue to next step.

2. CHECK CONNECTOR

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Disconnect SST from connector C.

(d) Check that the floor wire No. 2 connector (on the front seat outer belt RH side) is not damaged.

OK:

Lock button is not disengaged, or the claw of the lock is not deformed or damaged.

NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.

3. CHECK FLOOR WIRE NO. 2 (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)





(a) Disconnect the connectors from the center airbag sensor.

(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(c) Measure the voltage of the wire harness side connector.

Standard voltage:





(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(f) Measure the resistance of the wire harness side connector.

Standard resistance:





(g) Release the activation prevention mechanism built into connector B Diagnosis System.

(h) Measure the resistance of the wire harness side connector.

Standard resistance:





NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2

OK -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY