Installation
INSTRUMENT PANEL: LOWER INSTRUMENT PANEL: INSTALLATION
1. INSTALL LOWER INSTRUMENT PANEL
(a) Connect the connectors, attach the clamps and install the lower instrument panel.
(b) w/ Smart Key System:
Connect the connector.
(c) for Automatic Air Conditioning System:
Install the cooler thermistor hose and connect the connector.
(d) Attach the claws to install the DLC3.
(e) Install the 4 bolts, 2 screws and 2 clips.
2. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
(a) Attach the 3 claws to install the hood lock control lever.
3. INSTALL POWER STEERING ECU ASSEMBLY
(a) Install the ECU with the 3 nuts.
Torque : 8.5 Nm (87 kgf-cm, 75 in-lbf)
(b) Connect the connectors.
NOTICE:
Be sure to engage the lock of the connector as shown in the illustration.
4. INSTALL INSTRUMENT PANEL BOX
(a) Attach the 6 clips to install the instrument panel box.
(b) Install the screw.
5. INSTALL NO. 1 SWITCH HOLE BASE
(a) Connect the connectors.
(b) Attach the 4 clips to install the switch hole base.
6. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Attach the 3 claws to install the instrument panel under cover.
7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
(a) Attach the 8 claws to install the lower instrument panel finish panel.
(b) Install the 2 screws.
8. INSTALL COWL SIDE TRIM BOARD RH Installation
9. INSTALL COWL SIDE TRIM BOARD LH Installation
10. INSTALL FRONT DOOR SCUFF PLATE INSIDE RH Installation
11. INSTALL FRONT DOOR SCUFF PLATE INSIDE LH Installation
12. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY
(a) Install the rear console box with the 2 bolts and attach the wire harness clamp.
(b) Install the 2 screws.
13. INSTALL CONSOLE BOX CARPET
(a) Install the console box carpet.
14. INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER LH
(a) Attach the 2 claws to install the instrument panel bracket cover.
15. INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER RH
(a) Attach the 2 claws to install the instrument panel bracket cover.
16. INSTALL CONSOLE REAR END PANEL
(a) Attach the 6 claws to install the console rear end panel.
(b) for AC Power Supply:
(1) Connect the connectors and attach the wire harness clamp.
(2) Attach the 2 clips and 4 claws to install the console rear end panel.
17. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY
(a) Connect the connectors.
(b) Attach the 4 clips to install the upper rear console panel.
18. INSTALL CONSOLE CUP HOLDER BOX
(a) Attach the 2 clips to install the cup holder box.
(b) Install the 2 screws.
19. INSTALL SWITCH BASE
(a) Connect the connectors.
(b) Attach the 2 clips and 2 claws to install the switch base.
20. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY
(a) Connect the connector.
(b) Attach the 2 clips and 4 claws to install the floor shift position indicator housing.
21. INSTALL NO. 2 CONSOLE UPPER PANEL GARNISH
(a) Attach the 4 clips to install the upper panel garnish.
22. INSTALL NO. 1 CONSOLE UPPER PANEL GARNISH
(a) Attach the 4 clips to install the upper panel garnish.
23. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Twist the shift lever knob in the direction indicated by the arrow to install it.
24. INSTALL HEATER CONTROL SUB-ASSEMBLY (for Automatic Air Conditioning System) Installation
25. INSTALL HEATER CONTROL SUB-ASSEMBLY (for Manual Air Conditioning System) Installation
26. INSTALL COMBINATION SWITCH ASSEMBLY Installation
27. INSTALL SPIRAL CABLE SUB-ASSEMBLY Installation
28. INSTALL STEERING COLUMN COVER Installation
29. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(a) Install the upper instrument panel Installation.
30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
31. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light Diagnosis System.